Category: Arduino boards
Subcategories
There are 151 products.
Development board with AVR ATmega328 microcontroller with a clock signal of 16 MHz. Compatible with Arduino, it is equipped with a STEMMA QT connector. Adafruit 5597
Development board with ATmega328P microcontroller compatible with Arduino Uno Rev3. Waveshare R3 PLUS
Arduino MKR1000 Wifi with Headers
A miniature board with dimensions of 20x22 mm with an ATmega32U4 microcontroller. Compatible with Arduino Leonardo. DFRobot DFR0816
Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Arduino UNO kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun DEV-15444
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796
All-in-one microcontroller especially designed for robotics application. Benefit from Arduino open source platform, it is supported by thousands of open source codes, and can be easily expanded with most Arduino Shields. The integrated 2 way DC motor driver and wireless socket gives a much easier way to start your robotic project. DFR0004
Evaluation kit with Bluetooth 4.0 module. It has 8 digital pins, 4 analog pins and 4 PWM. Compatible with Arduino, it is perfect as a platform for building a small robot. DFRobot DFR0351
Development board compatible with Arduino. It has a built-in ATmega328P microcontroller and a Bluetooth BLE module (TI CC2540). DFRobot DFR0296
Module with the ATMega4809 microcontroller from the AVR family (48 KB Flash, 6 KB SRAM, 256 B EEPROM). The module has two 15-pin connectors equipped with GPIO, SPI, I2C, PWM, USART, DAC and ADC. Module with headers. Arduino ABX00033
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179
Base board compatible with Arduino. It was equipped with an ATmega328P microcontroller. It has 22 I / O lines (including 6 PWM channels) and 8 analog inputs and a Qwiic connector. SparkFun DEV-18158
Adafruit 1500
Beetle BLE is another milestone in wearable electronics device area based Arduino Uno, which makes DIY users have more options in the project design. It is fully compatible with Bluno in instructions and procedures, supporting Bluetooth HID and ibeacon modes. And it not only supports USB programming, but also wireless programming method. DFR0339
Module with dual-core STM32H747XI microcontroller with CortexM7+M4 core equipped with 2 MB flash memory, 1 kB RAM and clock speeds up to 480 MHz. The board has a built-in WiFi module and Bluetooth 5.1 (Murata 1DX). Arduino ABX00042
Plate from the Adafruit Feather series equipped with an ATmega32u4 microcontroller and a small prototype surface (5x7). The chip contains 32KB flash memory, 2KB RAM memory and built-in USB support. The plate is compatible with Arduino. Adafruit 2771
Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3677
Development kit with ATSAMD51J20 microcontroller with ARM Cortex M4F core. It is clocked at 120 MHz, has 1 MB of Flash and 256 KB of SRAM. There are 6 SERCOM interfaces on the board. SparkFun DEV-14713
Bluno - BLE with Arduino Uno
The board is equipped with ATSAMD51 microcontroller with ARM Cortex-M4 core and SPI Flash memory, communication interfaces and RGB diode. Adafruit 3382