Category: INTERNET OF THINGS (IoT)

Filter by

Manufacturers
more... less
Filter

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

zł35.60
24h
Available quantity: 182
Available

WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E

zł10.25
24h
Available quantity: 136
Available

Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD

zł16.53
24h
Available quantity: 99
Available

MCU module combining Wi-Fi and Bluetooth technologies (BR/EDR + BLE). Designed for a wide variety of IoT applications, from sensor networks to more demanding tasks such as voice encoding, music streaming, and MP3 decoding. Espressif ESP32-WROOM-32D 32MBit

zł16.57
24h
Available quantity: 71
Available

LoLin NodeMCU V3 is a board with ESP8266 (ESP12E). The ESP8266 system provides WiFi connectivity (802.11 b / g / n). The USB-UART converter (CH340G chip) is located on the board. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. There are 10 GPIO lines available.

zł14.90
24h
Available quantity: 69
Available

WiFi 802.11 b/g/n module with ESP8266 system, 16 terminals are available with a 2 mm pitch with the possibility of soldering gold pins, there are 9 GPIO lines and 1 ADC line on the connector. Built-in ceramic antenna and U.FL antenna connector. ESP-07

zł11.89
24h
Available quantity: 65
Available

Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini

zł20.02
24h
Available quantity: 65
Available

Espressif ESP32-C3 WiFi module board. It offers 4 MB of Flash memory and 400 kB of SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991054

zł28.60
24h
Available quantity: 45
Available

A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules

zł5.68
24h
Available quantity: 42
Available

The base board for the Wi-Fi NodeMCU module (ESP-12E), thanks to the built-in L293DD system, allows for attaching e.g. motors, electromagnets or other executive devices. The I/O lines of the NodeMCU module were derived to the pin connectors, and the power supply can be connected with the use of screw connectors. ESP12E Motor Shield

zł7.87
24h
Available quantity: 39
Available
XIAO ESP32S3 - ESP32-S3 WiFi and BLE module board
  • -zł4.37

Espressif ESP32-S3 WiFi and BLE module board. It offers 8 MB of flash memory and 8 MB of SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991114

Regular pricezł43.27zł38.90
24h
Available quantity: 34
Available

Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05

zł17.90
24h
Available quantity: 25
Available