![Feather RP2040 with DVI - board with RP2040 microcontroller and HDMI port](https://kamami.pl/79242-large_default/feather-rp2040-with-dvi-board-with-rp2040-microcontroller-and-hdmi-port.jpg)
![Feather RP2040 with DVI - board with RP2040 microcontroller and HDMI port](https://kamami.pl/79242-large_default/feather-rp2040-with-dvi-board-with-rp2040-microcontroller-and-hdmi-port.jpg)
zł67.03 tax excl.
Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The Feather RP2040 is a board featuring the RP2040 microcontroller designed by the Raspberry Pi Foundation. The chip has two ARM Cortex M0+ cores running at up to 133 MHz and 264 kB of RAM. The microcontroller is not equipped with flash memory, but there is an 8MB external memory on the board connected via the QSPI interface.
On the board, in addition to the RP2040 chip and flash memory, the user will find a 3.3 V voltage stabiliser, Boot and Reset buttons, NeoPixel LEDs and RGB LEDs, a USB type C connector for powering and programming the module, and 21 GPIO outputs, where peripherals such as four 12-bit ADC inputs, 16 PWM outputs, two I2C, SPI and UART interfaces are brought out. Additional sensors can be easily connected via the STEMMA QT connector and I2C interface.
An important part of the board is the HDMI connector, with which the Feather board can be used to display data on a monitor. The I2C pins of the HDMI connector are connected to the SDA/SCL of the RP2040 microcontroller (via a voltage level converter) so that the EDID EEPROM of the displays can be read. The user also has the CEC and Utility pins available, as well as the Hot Plug Detect pin. To support the HDMI display, the manufacturer provides an easy-to-use Arduino library.
The platform supports the popular MicroPython and C/C++ programming languages. Programs can be uploaded to the memory via the USB interface using the built-in bootloader.
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619
Development kit with SAMD21G18 microcontroller with ARM Cortex M0 core and LoRa RFM95 868/915 MHz radio communication module. Adafruit 3178
Adafruit Feather nRF52840 Express is an advanced development board with Bluetooth LE and native USB, perfect for mobile and portable applications. With ample memory, support for CircuitPython and Arduino IDE, and numerous interfaces, it is an excellent tool for creating advanced projects. Adafruit 4062
Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076
No product available!
Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458
Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231
The board is equipped with the STM32F405 microcontroller with the ARM Cortex-M4 core and SPI Flash memory, 20 GPIO pins, SD card slot, pins for connecting the battery with the charging and voltage stabilization circuit, JTAG connector and Qwiic socket. SparkFun DEV-17712
At the Feather 32u4\'s heart is ATmega32u4 clocked at 8 MHz and at 3.3V logic. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. Adafruit 2795
A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714
FeatherWing Proto - Prototyping Add-on For All Feather Boards
Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179
The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. Adafruit 3405
The board is equipped with a STM32F405 microcontroller with an ARM Cortex-M4 core and SPI Flash memory, GPIO pins, a connector for connecting a battery with a charging circuit and a STEMMA QT socket. Adafruit 4382
Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710