Adafruit 2884

Adafruit Feather 328P is a module with a built-in ATmega 328P AVR microcontroller (8MHz, 32kB Flash, 2kB RAM). The board is compatible with Arduino IDE, has small dimensions and low weight, and the built-in USB connector allows programming and debugging. Adafruit 3458

The board is equipped with a STM32F405 microcontroller with an ARM Cortex-M4 core and SPI Flash memory, GPIO pins, a connector for connecting a battery with a charging circuit and a STEMMA QT socket. Adafruit 4382

Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619

Development kit with nRF52840 microcontroller with ARM Cortex M4F core and BLE communication. Equipped with motion sensors, magnetometer, light, humidity, pressure sensors and a microphone. Adafruit 4516

The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884

FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. 256K FLASH, 32K RAM, built in USB and battery charging. Adafruit 2772

Development kit with SAMD21G18 microcontroller with ARM Cortex M0 core and LoRa RFM95 868/915 MHz radio communication module. Adafruit 3178

Adafruit Feather HUZZAH ESP8266 is a new development board from Adafruit with a built-in WiFi module ESP8266. Processor frequency: 80 MHz, USB-serial TTL CP2104 converter, Li-Pol battery charger. Adafruit 2821

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477

Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710

Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3010

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796