Feather RP2040 with DVI - board with RP2040 microcontroller and HDMI port
ID: 1184876
5906623470358
zł85.77
Tax included
zł69.73 tax excl.
Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710
Description
The Feather RP2040 is a board featuring the RP2040 microcontroller designed by the Raspberry Pi Foundation. The chip has two ARM Cortex M0+ cores running at up to 133 MHz and 264 kB of RAM. The microcontroller is not equipped with flash memory, but there is an 8MB external memory on the board connected via the QSPI interface.
On the board, in addition to the RP2040 chip and flash memory, the user will find a 3.3 V voltage stabiliser, Boot and Reset buttons, NeoPixel LEDs and RGB LEDs, a USB type C connector for powering and programming the module, and 21 GPIO outputs, where peripherals such as four 12-bit ADC inputs, 16 PWM outputs, two I2C, SPI and UART interfaces are brought out. Additional sensors can be easily connected via the STEMMA QT connector and I2C interface.
An important part of the board is the HDMI connector, with which the Feather board can be used to display data on a monitor. The I2C pins of the HDMI connector are connected to the SDA/SCL of the RP2040 microcontroller (via a voltage level converter) so that the EDID EEPROM of the displays can be read. The user also has the CEC and Utility pins available, as well as the Hot Plug Detect pin. To support the HDMI display, the manufacturer provides an easy-to-use Arduino library.
The platform supports the popular MicroPython and C/C++ programming languages. Programs can be uploaded to the memory via the USB interface using the built-in bootloader.
Features
- RP2040 microcontroller designed by Raspberry Pi
- Two ARM Cortex-M0+ cores clocked at up to 133 MHz
- 264 kB of on-board SRAM
- Real-time clock (RTC)
- HDMI connector
- Voltage regulator 3.3 V 500 mA
- Battery charging circuit 200 mA
- Built-in USB Type C connector for programming with USB 1.1 operating in Host and Device modes
- 21 x multifunctional GPIO pins
- 4 x 12-bit ADC inputs with internal temperature sensor, 0.5 MSa/sec.
- 16 PWM channels
- 2 x UART
- 2 x I2C
- 2 x SPI
- Reset and Boot buttons
- LEDs and NeoPixel
- LiPo battery connector
- STEMMA QT connector compatible with Qwiic systems
- SWD interface connector
- 8 MB external Flash memory
- Supported programming languages: MicroPython and C/C++
- Dimensions: 53 x 23.3 x 7.7 mm
Kit contains
- Feather RP2040 with DVI
- 2 x 16-pin male goldpin connector
1184876
Data sheet
- Microcontroller
- RP2040
- Flash memory
- 8 MB
- Number of I/O
- 21
- Ethernet
- none
- WiFi/BT module
- No
- Bluetooth module
- No
- MicroSD slot
- No
- Length
- 53 mm
- Width
- 23,3 mm
- USB connector type
- USB type C
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
zł5.83
24h
Available quantity: 12
Available
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
zł5.29
24h
Available quantity: 26
Available
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
zł7.50
24h
Available quantity: 3
Available
Other products in the same category (16)
Module with WiFi Espressif ESP32-S2. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5000
zł87.88
24h
Available quantity: 1
Available
This compact IoT board features a dual-core 240 MHz processor, 2.4 GHz WiFi, and Bluetooth LE. The w.FL antenna connector allows for an external antenna, increasing range and stability. The board offers 8 MB of Flash, 512 KB of SRAM, native USB with HID and MIDI support, and a built-in LiPo charger with a MAX17048 battery monitor. It also includes a STEMMA QT connector, a programmable NeoPixel, and full compatibility with the Feather ecosystem. The Adafruit 5885
zł88.26
24h
Available quantity: 1
Available
The board is equipped with the ATSAMD51J19 microcontroller with ARM Cortex-M4 core and SPI Flash memory, GPIO pins, connector for connecting the battery with the charging circuit. Adafruit 3857
zł119.31
24h
Available quantity: 1
Available
A board with an RP2040 microcontroller and a radio module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and a STEMMA QT connector. Adafruit 5712
zł121.44
24h
Available quantity: 4
Available
Adafruit Feather HUZZAH ESP8266 is a new development board from Adafruit with a built-in WiFi module ESP8266. Processor frequency: 80 MHz, USB-serial TTL CP2104 converter, Li-Pol battery charger. Adafruit 2821
zł90.18
24h
Available quantity: 1
Available
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. The board has soldered goldpin connectors. Adafruit 3591
zł152.38
4 weeks
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884
zł79.03
24h
Available quantity: 5
Available
Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477
zł90.95
24h
Available quantity: 3
Available
A compact development board with a built-in 1.14" IPS display, ideal for user interfaces, IoT projects, and case-mounted devices. Featuring the ESP32-S3 with Wi-Fi, Bluetooth LE, and native USB, it offers 4MB of Flash and 2MB of PSRAM to support more advanced graphics and networking applications. Three user buttons, a STEMMA QT connector, and an integrated LiPo charger provide convenient prototyping and expansion capabilities. Adafruit 6303
zł125.84
24h
Available quantity: 1
Available
Board with RP2040 microcontroller and class D mono audio amplifier based on MAX98357 chip. It has a built-in LIS3DH three-axis accelerometer, an RGB NeoPixel LED, a LiPo charging circuit, and a STEMMA QT connector. Adafruit 5768
zł122.47
24h
Available quantity: 7
Available
Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046
zł111.73
24h
Available quantity: 2
Available
The board is equipped with a STM32F405 microcontroller with an ARM Cortex-M4 core and SPI Flash memory, GPIO pins, a connector for connecting a battery with a charging circuit and a STEMMA QT socket. Adafruit 4382
zł217.59
24h
Available quantity: 1
Available
Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076
zł147.12
4 weeks
No product available!
Module with WiFi Espressif ESP32-S2. It integrates the TFT LCD display, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5300
zł144.23
24h
Available quantity: 2
Available
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, the module has a built-in system for charging Li-Pol batteries. The plate has soldered goldpin connectors (female extension). Adafruit 3619
zł157.76
4 weeks
No product available!
A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714
zł175.46
24h
Available quantity: 2
Available
Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710