- Out-of-Stock
AVT2469 A
ID: 190177
UKF FM RECEIVER - PRINTED PLATE
UKF FM RECEIVER - PRINTED PLATE
Producer: AVT
Simple to assemble and start up, a miniature FM receiver. The system uses a factory-prepared and tuned UKF head. It is made in SMD technology and tuning ranges takes place in a voltage. There are two integrated circuits on the receiver board. The first one contains intermediate frequency circuits, the second one is an acoustic amplifier. The station can be listened to via a small loudspeaker. Tuning of the entire receiver is carried out using the "listen" method, without the need for specialized measuring devices. Thanks to this kit can be made even less experienced electronic engineers.
The device is especially recommended for radio enthusiasts and constructors of listening receivers
Selected parameters:
- UKF mono receiver
- tune - liquid, voltage
- sound transducer - a miniature speaker
- smooth volume control
- 2 W output power (8 ohm speaker, 12V power supply)
- power supply - 12 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available- Detailed description in
Download
190177
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
T-Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). Goldpin connectors are included, for self-assembly. Adafruit 1989
Retired
No product available!
FPC tape length 250 mm, 50 lines, pitch 0.5 mm. Adafruit 1682
Retired
No product available!
μHex is the first low-power controller which is compatible with Arduino. It is very suitable for the battery power supply environment. A 210mAh CR2032 cell battery could make it work 60 days long. DFR0343
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Delivery date unknown
No product available!
The DE0-Nano-SoC Development Kit presents a robust hardware design platform built around the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility
Retired
No product available!
Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm
Retired
No product available!
No product available!
No product available!
FRAM memory with a capacity of 4kbit by Cypress Semiconductor, communicates via the I2C bus, the power supply voltage is in the range 2.7 - 3.6V. The system has an SOIC8 housing
Retired
No product available!
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
Retired
No product available!
Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm
Delivery date unknown
No product available!
KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO
Retired
No product available!
K64 microcontroller with ARM® Cortex®-M4 core, 1MB Flash memory, 256kB RAM, 120MHz, SPI, I2C, I2S, UART, CAN, USB OTG, ADC, DAC, RTC, DMA, LQFP100
Retired
No product available!
SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902
Retired
No product available!
Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors: 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope. Adafruit 2020
Retired
No product available!
UKF FM RECEIVER - PRINTED PLATE