Category: STARTER KITS, PROGRAMMERS, MODULES
Kamami.pl electronics store offers a wide range of starter kits for microcontrollers and programmable devices as well as accessories (programmers, modules, etc.).
Subcategories
-
Atmel SAM
-
Atmel Xplain
-
AVR
-
Banana Pi
-
BeagleBone
-
chipKIT
-
CPLD Xilinx
-
Cubieboard
-
DFRobot FireBeetle
-
Analog electronics
-
Feather
-
Alchitry FPGA
-
Altera FPGA
-
Xilinx FPGAs
-
Freedom (Kinetis)
-
FriendlyELEC
-
Coral
-
HummingBoard
-
Other development kits
-
Intelligent clothes
-
LattePanda
-
LPC (NXP)
-
M5Stack
-
Micro:bit
-
Peripheral modules
-
Nvidia Jetson
-
Odroid
-
ODYSSEY
-
Orange Pi
-
PIC
-
Segger programmers
-
Universal programmers
-
Raisonance
-
Raspberry Pi RP2040
-
RFID
-
RISC-V
-
SBC Embest
-
SBC MYIR
-
SBC UDOO
-
SBC others
-
SoMLabs
-
Sparkfun MicroMod
-
STM32
-
STM32 MP1
-
STM32 Discovery
-
STM32 Nucleo boards
-
STM8
-
Teensy
-
WRTNode
-
Kit with a book
There are 2731 products.
STM32 Nucleo-64 development board with STM32F446RET6 MCU, supports Arduino and ST morpho connectivity
Simulation set for Siemens S7-1200 PLC devices. Using this set, it is possible to verify the operation of a program written for a PLC by applying the appropriate states to the digital inputs, to the analogue (ADC) inputs voltages from the built-in or external sensors. LED status monitoring is possible
StarSBC series minicomputer with NXP i.MX6 ULL Y2 792MHz processor (Cortex-A7 core), 512MB RAM, 8GB eMMC memory, built-in WiFi and Bluetooth wireless and wired Ethernet connectivity. SoMLabs SLC2X6Y2_792C_512R_08GE_3WE_C
Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function
RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming
Multifunctional board for STM32 NUCLEO, built based on operational amplifiers. Has, among others built-in LED current controller, prototype area and window discriminator
Robert Wołgajew
Universal EEPROM and Flash serial memory programmer. It is controlled from the computer via the USB interface and software for Windows systems. modCH341set1
Switched-mode AC Power supply 12V/2A with DC 5.5x2.1 connector and EU plug. It has anti-overload, anti-overvoltage, short circuit protection. Conform to the norm Energy efficiency Level V. Length of output cable is 1.2m
Cable that allows you to attach the ATMEL-ICE programmer to the development kit with any connector (supported by the programmer), via single pin plugs (goldpin)
The STM32F7 discovery kit allows users to develop and share applications with the STM32F7 Series microcontollers based on ARM® Cortex®-M7 core.
StarCB-6ULL-STD v.1.1 is the base board for StarSOM-6ULL (i.MX6 ULL) modules. The board contains, among others Ethernet and USB connectors, connectors compatible with Raspberry Pi HATami, 5 buttons and 5 LEDs. SoMLabs StarCB-6ULL-STD v.1.1
SpaceSOM series module with NXP i.MX8M plus 1.6 GHz processor (4 Cortex-A53 + Cortex-M7 cores), 2 GB RAM and 8 GB eMMC memory. SomLabs SLS35X8MPQC_1600C_02GR_08GE_0SF_E
StarSBC series minicomputer with NXP i.MX6 ULL Y2 792MHz processor (Cortex-A7 core), 512MB RAM, 8GB eMMC memory, built-in WiFi and Bluetooth wireless connectivity. SoMLabs SLC2X6Y2_792C_512R_08GE_1WB_E
The adapter allows you to connect the antenna with the SMA 50 Ω female connector to the device with the uFL socket (also known as u.FL, IPEX, IPAX, IPX, MHF, AM). The cord has a length of 20cm.
StarSOM series module with NXP i.MX6 ULL Y2 792MHz processor (Cortex-A7 core), 512 MB RAM memory and 4 GB eMMC memory. SomLabs SLS06Y2_792C_512R_04GE_2ET_C
StarSBC-6ULL minicomputer with i.MX6ULL processor, 512MB RAM and 8GB eMMC and 8GB eMMC memory. SoMLabs SLC2X6Y2_792C_512R_08GE_0SF_I