Angled male socket, wire-board type, for JST PH-2.0 wires, 6-pin, 2mm pitch, 100V, 2A. Set of 10 pieces

GPS Receiver, Digilent, RoHS

Module with 2 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4202

Pololu High-Power Motor Driver 18v25 CS

RC extension cable dedicated to servos, comes with JR/Futaba female and male connectors. It has twisted wires

Non-contact temperature sensor with a measuring range from -70 to 380°C. It uses infrared waves and has a current output. DFRobot SEN0264

Module with a black and white OLED display with a diagonal of 1.12" and a resolution of 128x128 px. The board is equipped with a Grove connector and communicates via the I2C and SPI interface. Seeed Studio 104020250

The Akyga AK-ND-C07 adapter converts a USB-C connector to an HP 7.4x5.0 mm laptop connector, allowing you to charge various HP laptop models with one USB-C PD charger. The adapter supports power up to 100 W and voltage from 18.5 to 20 V. It is compact, which makes it perfect for travel. It is important to check the power of the power supply you are using before connecting. Akyga AK-ND-C07

USB - UART converter based on the CH9102F chip. Compatible with the voltage of 3.3 V and 5 V, it has been equipped with a USB type C connector. Adafruit 5568

Antenna with RP-SMA male plug operating in the 433 MHz frequency band. It has a gain of 3 dBi

The Akyga AK-ND-C14 USB-C adapter allows you to use USB-C PD chargers in older Sony Vaio laptops with a 6.5x4.4 mm connector. It works with Power Delivery technology, automatically adjusting the supply voltage. It is easy to use and allows you to adapt your devices to USB-C standards. Before use, make sure the power supply has the appropriate power. Akyga AK-ND-C14

Compact ORP system compatible with Arduino. It allows you to monitor the ORP without having to add additional circuits or components. DFRobot SEN0165

4-digit 7-segment 0.56 "LED display. Built-in HT16K33 controller allowing communication via I2C bus. Equipped with STEMMA QT connector. Adafruit 5599

Base board for Xbee radio modules belonging to the Series 1, Series 2 and Pro families. Equipped with a voltage regulator, 3.3V to 5V level converters and LEDs for Power, RSSI and DIN / DOUT lines. SparkFun WRL-11373

This disc load cell (sometimes called a strain gauge) can translate up to a whopping 200kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the disc. SEN-13332

This compact board breaks out the pins of a microSD card connector necessary to interface with the card through SPI (Serial Peripheral Interface), and it can be directly integrated into 5 V systems thanks to its on board 3.3 V regulator and level shifting circuity. Pololu 2587

Antenna with SMA male plug operating in the 2.4 GHz frequency band. It has a gain of 7 dBi and a cable. Magnetically attached

The Akyga AK-ND-C06 adapter allows you to transform the USB-C connector into a 3.0x1.0 mm plug, typical for some older Acer and Samsung laptops. Allows you to charge devices with a power of up to 100 W using the universal USB-C PD charger. Before use, it is important to make sure that the power supply you are using has the appropriate power. Akyga AK-ND-C06

The Lanberg Cat. 8.1 patch cord with Fluke Passed certification guarantees top quality and reliability, enabling optimal network connections compatible with various networking devices in any environment. Lanberg PCF8-10CU-0200-B

LoRa radio module with 433 MHz operating frequency. Communication takes place via the UART serial interface. It is supplied with the voltage in the range from 3.4 to 5.5 V. DFRobot TEL0116