USB-UART converter module based on the CH9102F chip. It offers transmission speeds up to 3 Mbps and the ability to reconfigure the internal settings of the system. The user has access to all lines that are led out on connectors with a 2.54 mm pitch. The CH9102F has fairly good driver support and 99% of the time it is a good replacement for the FTR232, FT231x or CP210x series. The converter can work with a voltage of 3.3 V or 5 V and is powered by a USB type C connector. It is perfect as a module for cooperation with Arduino, ESP32 or ESP8266. Configuration examples are available on the product page.
Manufacturer
Responsible person
Cable with USB typ A and USB typ C connectors, cable length 0.5 m. LANBERG
Cable with USB typ A and USB typ C connectors, cable length 1 m. LANBERG CA-USBO-10CC-0010-BK
Cable with USB type A and USB type C 2.0 plugs, cable length 1 m
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
The UART-USB converter built on the FTDI FT232RL chip. Compatible with 3.3V and 5V voltages. DFRobot DFR0065
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, it is equipped with a microUSB connector. Cytron UC00A
USB - UART TTL converter based on the FT232RL chip, the module is equipped with a miniUSB socket. Works with 3.3V or 5V voltage levels.
USB port isolator based on the ADUM3160 chip. The device has a rated insulation voltage of 1500V. The isolator is powered from the USB port.
A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules
UART-RS232 converter module. The board was equipped with a Grove and DB9 connector. Seeed Studio 103020192
USB adapter designed for XBee modules. It can be connected to a computer with a USB cable and used with the X-CTU software to configure the XBee. DFRobot DFR0174
RS232 - UART converter module based on the MAX3232 chip. There is a DB9 connector on the board and a 4-pin connector with a 2.54 mm pitch
USB - RS-232 USB A (m) / D-Sub (m) cable with a length of 1 m. Akyga AK-CO-02
The module with the UART-RS232 converter is designed to work with the Raspberry Pi Pico. It has a built-in SP3232EEN chip and enables data transmission between the UART interface and the RS232 device. Waveshare Pico-2CH-RS232
The base plate is dedicated to ESP32 CAM modules. It allows you to connect the camera via a USB interface, e.g. to a computer. ESP32-CAM-MB
A module with a USB converter - GPIO/ADC/I2C based on the MCP2221A chip. It allows you to connect sensors, displays or PWM drivers to the computer via a 2.54 mm or Stemma QT/Qwiic connector. Adafruit 4471
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, has been equipped with a USB type C connector. Waveshare FT232 USB UART Board (Type C)
No product available!
USB - UART converter based on the CP2102 chip. Compatible with a voltage of 3.3 V, has been equipped with a USB type C connector. Waveshare CP2102 USB UART Board (Type C)
USB - UART converter based on the PL2303 chip. Compatible with voltages of 1.8 V, 2.5 V, 3.3 V and 5 V, it is equipped with a USB type C connector. Waveshare PL2303 USB UART Board (Type C)
No product available!
USB - UART converter based on the CH9102F chip. Compatible with the voltage of 3.3 V and 5 V, it has been equipped with a USB type C connector. Adafruit 5568