

USB - UART converter module based on the popular FT232RNL chip by FTDI. The user has access to all lines of the system that are led out on connectors with a 2.54 mm pitch. The converter can work with the voltage of 5 V or 3.3 V and is powered by the USB connector or by the goldpin connectors. Depending on the position of the configuration jumper, the user can use the voltage of 3.3 V or 5 V to supply external systems. Full documentation is available on the product Wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Cable with USB plugs type A and mini-USB type B, cable with a length of 1.8 m
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. DEV-09716
No product available!
UART - USB converter based on the FT232RL chip with TX, RX, RTS and CTS lines led out to the pin connector, the remaining lines available on solder fields for pin connectors. Micro-USB socket. Voltage supply from 3.3 to 5 V. FT232 USB UART Board (micro)
USB TO UART solution with USB Type A connector
USB - UART converter based on the FT232RL chip. Compatible with voltages of 3.3 V and 5 V, has been equipped with a USB type C connector. Waveshare FT232 USB UART Board (Type C)
Cable with USB plugs type A and miniUSB type B 2.0, cable length 0.3 m. LANBERG CA-USBK-10CC-0003-BK
No product available!
No product available!
USB - UART converter based on the PL2303 chip. Compatible with voltages of 1.8 V, 2.5 V, 3.3 V and 5 V, it is equipped with a USB type A connector. Waveshare PL2303 USB UART Board (type A) V2
Overlay module for Raspberry Pi with GSM, GPRS, GNSS and Bluetooth
KAmod RS232S-mini is a miniature RS232 to TTL converter with a female DB9 connector, 2.54 mm goldpin pins, operating at 3-5.5 V, supporting all RS232 signals, based on the MAX3238/SP3238 chip, offering ESD protection up to 15 kV and corresponding to a DCE/Modem device
A small USB-UART TTL converter module based on the CH340 system with a USB type A connector. Designed for the ESP-01 and ESP-01S modules
USB - UART TTL converter based on the FT232RL chip, the module is equipped with a miniUSB socket. Works with 3.3V or 5V voltage levels.
Versatile USB protocol converter, offering four channels (RS485, RS232, two TTL) and 12V, 5V and 3.3V power supply, ideal for IoT and industrial applications. Compatible with Windows, Linux, LattePanda and Raspberry Pi, no drivers required, and optional installation allows easy device management. DFRobot TEL0185
The module with the UART-RS232 converter is designed to work with the Raspberry Pi Pico. It has a built-in SP3232EEN chip and enables data transmission between the UART interface and the RS232 device. Waveshare Pico-2CH-RS232
KAmod RS232H-ALL is a RS232 to TTL signal converter, supporting all RS232 interface signals, based on the MAX3243/SP3243 system, with a TTL side voltage of 3-5.5 V, a maximum transmission speed of 250 kbps, ESD protection up to 15kV HBM, a standard DB9 connector, a Phoenix MC 3.81 connector and 2.54 mm goldpin pins, with a board size of 65x30 mm (72x30 mm with a DB9 connector
UART converter - USB based on the FT232RL system with TX, RX, RTS and CTS lines led out to the goldpin female connector. It uses a mini USB connector. Adafruit 284
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
UART-RS232 converter module. The board was equipped with a Grove and DB9 connector. Seeed Studio 103020192
A module with a USB converter - GPIO/ADC/I2C based on the MCP2221A chip. It allows you to connect sensors, displays or PWM drivers to the computer via a 2.54 mm or Stemma QT/Qwiic connector. Adafruit 4471
No product available!
USB - RS232/RS485 converter with the original FT2132RNL chip. It uses a USB type A connector and a screw connector to connect RS232 and RS485 interfaces. Supports a wide range of operating systems: Mac, Linux, Android and Windows 11, 10, 8.1, 8, 7. Waveshare USB TO RS232/485
USB - UART converter based on the FT232RNL chip. Compatible with voltages of 3.3 V and 5 V, it has been equipped with a miniUSB connector. Waveshare FT232 USB UART Board (mini)