The base board is dedicated to ESP32 CAM modules. It has two buttons built-in (RST), a USB-UART converter with CH340 chip. It allows you to connect the camera via a USB interface, e.g. to a computer.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CCP-MUSB2-AMBM-W-1M
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-BK
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. LANBERG CA-USBM-10CC-0018-W
Cable with USB typ A and microUSB typ B connectors, cable length 1 m. LANBERG CA-USBM-10CC-0010-BK
Board with WiFi and BLE Espressif ESP32-S3 module and OV3660 camera and digital microphone. It offers 8 MB Flash memory and 8 MB SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991115
LCD TFT display with a diagonal of 2.4 "and a resolution of 320x240 pixels. Equipped with a resistive touch panel and microSD slot. Designed for use with Feather series plates. Adafruit 3315
No product available!
Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221
The MAX31865 amplifier module is an ideal tool for accurate temperature measurement in various applications. It is compatible with 2, 3 or 4-wire PT100 RTD temperature probes. Adafruit 3328
No product available!
Two-channel DC motor driver communicating via UART, SPI or I2C interface. It can control the movement of 3 to 11V motors with a maximum continuous current of 1.2A per channel. SparkFun ROB-13911
No product available!
This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This low-brightness version draws an average of 8 mA at 5 V and has a typical sensing range up to approximately 12 inches (30 cm).
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 3.3 V with an available output current of around 15 A. Pololu 2880
No product available!
Step-Down DC-DC converter module based on the D24V150F12 chip. Input voltage 14.5 ... 40V, output voltage 12V (max 15A). Pololu 2885
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
IPS, 1280×800, 10.1 inch Capacitive Touch Screen LCD, Supports Multi mini-PCs, Multi Systems, for Raspberry Pi and other boards
The BME280 integrated circuit is a sensor of atmospheric conditions (pressure, humidity, temperature) in the SMD casing (2.5mmx2.5mm). The sensor has very low power consumption (average 3.6uA) and has an I2C / SPI bus. The Bosch Sensortec system
No product available!
A set of four M12 lenses is an ideal choice to be used with oCam series cameras. Lens set without IR cut filter
Zynq-7000 All Programmable SoC, Dual ARM Cortex-A9 MPCore, Artix-7 FPGA, 85K Logic Cells, 256KB 667MHz CSPBGA400, Xilinx
No product available!
32-bit microcontroller with ARM Cortex-M0 core, XMC1200, 32kB Flash, TSSOP-16, Infineon
No product available!
32-bit microcontroller with ARM Cortex-M0 core, XMC1100, 32kB Flash, TSSOP-16, Infineon
No product available!
32-bit microcontroller with ARM Cortex-M0 core, XMC1100, 64kB Flash, TSSOP-38, Infineon
No product available!
32-bit microcontroller with ARM Cortex-M0 core, XMC1300, 32kB Flash, TSSOP-16, Infineon
No product available!
The base plate is dedicated to ESP32 CAM modules. It allows you to connect the camera via a USB interface, e.g. to a computer. ESP32-CAM-MB