The 0.5 meter long cable that allows you to transfer a 4K image at 60Hz, is characterized by high quality and compatibility with a wide range of devices equipped with a USB-C port with DP Alt Mode and DisplayPort. Lanberg CA-CMDP-10CU-0005-BK

Bluetooth audio receiver module enclosed in a housing that enables wireless transmission of sounds. It is equipped with a PCB antenna, microphone, 3.5 mm audio jack and control buttons

ACS711EX Current Sensor Carrier -31A to +31A

Efficient step-down converter that reduces the input voltage from up to 45 V to a regulated output voltage range from 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in protection against reverse polarity, overload and short circuit, and the spread spectrum function reduces EMI interference. The module is equipped with an additional potentiometer for adjusting the cut-off voltage. Pololu 4872

Precision Hall effect current sensor offering galvanic isolation, wide bandwidth of 150 kHz and the ability to measure AC and DC current with very low power loss. Thanks to differential measurement and immunity to magnetic interference, it is perfect for applications requiring accurate current monitoring, such as power supplies, converters or motor control systems. Pololu 5291

TSV522IQ2T, High merit factor (1.15 MHz for 45 μA) CMOS op amps, DFN-8

LMV821ILT, Low power (440uA), general purpose BiPolar 5V Op-Amp, GBP=5.5MHz, single, SOT-23-5

Male terminal block, angled, 5-pin. Pitch 3.81mm. Height 7mm. 15EDGRC. Set of 10 pieces

Temperature sensor based on the DS18B20 system in a water proof measuring probe. Communication via the 1-Wire interface. DFRobot DFR0198

IPS LCD display with a diagonal of 6.25" and a resolution of 720x1560 pixels. It uses an HDMI connector for image transmission and has a built-in capacitive touch panel controlled via a USB Type-C connector. It is dedicated to users of Raspberry Pi, NVIDIA Jetson Nano minicomputers and PCs. Waveshare 6.25 inch 720x1560 LCD

ARM Cortex-M3 CPU, Low power, 256kB Flash, 32kB RAM, USB, 3xUART, 2xI2C, 2xSPI, ADC, DAC, STM, LQFP64, RoHS

Pololu 4814 is a set of two JST SH 4-pin top-entry adapters that allow easy integration of JST SH wires with breadboards and prototype boards. With support for voltages up to 50 V and currents up to 1 A per pin, these adapters are suitable for a wide range of applications in electronics and automation.

Diagnostic interface for wireless diagnostics of cars with OBD2 system. The device uses the popular 16-pin connector and is equipped with a Bluetooth 2.0 module. ELM327 Mini V1.5

SD and microSD memory card reader module. It communicates via the SPI interface. DFRobot DFR0071

MicroSD and microSDHC memory card reader with USB 2.0 and microUSB interface. GoodRam AO20-MW01R11

Step-Down converter with an output voltage of 5 V, input voltage from 4.5 to 40 V and a maximum current of 2 A. The board is equipped with a segment LED display and a USB output

LCD 2x16, 53x20mm SMALL, LED backlight (WHITE) NEGATIVE BLUE, STN, enhanced temperature range, ZIFF connector for FCC tape, 3.15mm character

Audio receiver with Bluetooth 4.2 module. It is powered by a microUSB connector or a battery and is equipped with a charging circuit

Module dedicated to Raspberry Pi, which supports various wireless communication modes, such as LTE-TDD, LTE-FDD, GSM, GPRS and EDGE. With download speeds of up to 10Mbps and upload speeds of up to 5Mbps, this module is perfect for IoT applications such as remote information processing, device monitoring, POS terminals, industrial routers, remote diagnostics and satellite positioning. Waveshare A7670E Cat-1/GNSS HAT

Active USB 3.0 Hub with 4 ports and a phone holder. It allows you to extend the number of USB ports on your computer and connect multiple devices at the same time