PC817 module with 4 optocouplers
ID: 1183107
5906623466665
zł6.65
Tax included
zł5.41 tax excl.
A module with 4 PC817 optocouplers. Allows you to add galvanic separation in the form of opto-isolation between electrical circuits
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
A module with 4 PC817 optocouplers. Allows you to add galvanic separation in the form of opto-isolation between electrical circuits. It provides information exchange by physically separating the circuits, which increases the safety of the device and reduces the impact of interference. It is used in automation, control systems and switching power supplies.
Features
- Number of channels: 4
- PC817 optocoupler
- Input voltage: 3.6 V to 24 V
- Output voltage: 3.6 V to 30 V
- Jumpers for output configuration (Pull-Down or High-Z)
- Dimensions: 38 x 48 mm
1183107
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A module with two PC817 optocouplers. Allows you to add galvanic separation in the form of opto-isolation between electrical circuits
zł4.49 Delivery date unknown No product available!
Other products in the same category (16)
Audio expansion module with CS4344 24-bit DAC converter. Numato Lab EXPAUD002
zł107.19 6 weeks No product available!
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł49.80 24hAvailable quantity: 5 AvailableServo driver based on the Raspberry Pi RP2040 microcontroller. It allows you to control up to 18 servos, has 6 analog inputs and a QW/ST connector for connecting additional sensors. Pimoroni PIM613
Regular pricezł125.05zł123.86 24hAvailable quantity: 9 AvailableKAmod RS232H-ALL is a RS232 to TTL signal converter, supporting all RS232 interface signals, based on the MAX3243/SP3243 system, with a TTL side voltage of 3-5.5 V, a maximum transmission speed of 250 kbps, ESD protection up to 15kV HBM, a standard DB9 connector, a Phoenix MC 3.81 connector and 2.54 mm goldpin pins, with a board size of 65x30 mm (72x30 mm with a DB9 connector
zł32.30 24hAvailable quantity: 193 Available4-channel converter of logic levels allowing for connection of systems operating with voltage levels of 1.8 V, 2.5 V, 3.3 V and 5 V. DFRobot DFR0843
zł19.56 24hAvailable quantity: 3 AvailableAudio player and recorder with built-in VS1003 codec, 3.5 mm jack audio output and a microphone
zł34.21 24hAvailable quantity: 2 AvailableRS485 - Ethernet converter that provides easy communication between the RS485 and RJ45 Ethernet interface. Configurable via website or AT commands. Waveshare RS485 TO ETH (for EU)
zł147.96 24hAvailable quantity: 3 AvailableTouch keyboard module with 4 buttons based on the TTP224 system. It is equipped with a connector with derived signals and 4 LEDs signaling the state of each button
zł5.87 24hAvailable quantity: 1 AvailableModule with three 4-20 mA analog outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3078ADAM
zł285.56 24hAvailable quantity: 2 AvailableModule with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
zł437.79 24hAvailable quantity: 1 AvailableThe module is dedicated to home automation based on the Raspberry Pi. It allows you to control two devices 250VAC/7A or 30VDC/10A, providing isolation with an optocoupler. SB Components 21932
zł92.39 24hAvailable quantity: 1 AvailableStereo audio preamplifier based on two uPC4570C operational amplifiers. It allows you to control the bass, treble and volume level
zł210.17 24hAvailable quantity: 1 AvailableAudio module with DAC converter and mono amplifier, designed to work with the Raspberry Pi. Pimoroni PIM541
zł58.79 4 weeks No product available!
A 5-channel flame detector module for detecting a flame over a larger area. Detects fire with 5 sensors that are placed on the module every 30 degrees. It has a digital and analog output. modFLAME-5CH
zł34.10 24hAvailable quantity: 2 AvailableClock & Timer Development Tools Gravity I2C SD2405 RTC. DFR0469
zł45.99 24hAvailable quantity: 2 Available2-channel module with relays, designed to work with the Raspberry Pi. It can switch 250VAC/7A or 30VDC/10A signals. SB Components 14088
zł57.90 24hAvailable quantity: 2 Available
A module with 4 PC817 optocouplers. Allows you to add galvanic separation in the form of opto-isolation between electrical circuits