![Adafruit Feather HUZZAH ESP8266 with soldered connectors](https://kamami.pl/79146-large_default/adafruit-feather-huzzah-esp8266-with-soldered-connectors.jpg)
![Adafruit Feather HUZZAH ESP8266 with soldered connectors](https://kamami.pl/79146-large_default/adafruit-feather-huzzah-esp8266-with-soldered-connectors.jpg)
zł90.84 tax excl.
Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
The Feather series are Adafruit's flagship development tiles. The development board was based on the ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. The module has a USB-UART converter with a maximum transmission speed of 912 600 bit / s. A 3.7V LiPol battery can also be connected to the PCB, which can be charged through the board. The board also allows you to power from the USB connector.
Easy-to-use retractable cable with USB type A plugs and micro-B type, the cable has a length of 73 cm
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650
No product available!
7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088
Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5477
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0+ cores, which work at a frequency of 133 MHz, 256 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Adafruit 4884
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
Adafruit Feather M0 WiFi with uFL - ATSAMD21 + ATWINC1500 is a development board with a 32-bit ATSAMD21G18 microcontroller based on Cortex-M0 core. The board also has an ATWINC1500 module that provides WiFi connectivity. Adafruit 3061
No product available!
Gamepad module (game controller) with joystick and buttons. Designed for Feather tiles. Adafruit 3632
The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702
Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449
A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890
At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much). Adafruit 2796
Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. Adafruit 3405
Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417
Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046