- Out-of-Stock
COM-10878 - EL Escudo Dos
Description:
Weve heard you, and made a number of improvements to our EL Shield. The new version adds zero-crossing optoisolated triacs for noise-free operation and full isolation between the AC and DC sides, and includes a 1.5A adjustable linear regulator to supply regulated DC to an external inverter (not included).
EL Escudo Dos is an Arduino shield for controlling up to eight strands of electroluminescent wire. EL wire is flexible plastic cord that glows brightly when high-voltage AC is applied to it. Its available in numerous colors (see the related products below), runs cool, and requires very little current, but can be difficult to work with because of the high-voltage requirements. The El Escudo Dos contains circuitry to safely switch high-voltage AC on and off, allowing you to create animated displays or whatever else your imagination can come up with.
In addition to this shield, you will need Arduino headers (see the related products below), an inverter (a component that generates the high-voltage AC needed by EL wire), and the EL wire itself. SparkFun carries two inverters, a 3V-input version that can drive a few feet of EL wire, and a 12V-input version capable of driving dozens of feet of EL wire. Choose the one appropriate to your power source and driving requirements. The shields built-in regulator comes preset to 3.3V, but can be set to any voltage by changing two resistors, or bypassed with a solder jumper to send the Arduinos RAW voltage directly to the inverter (perfect for 12V setups!). See the tutorial below. Nate has used EL wire to make amazing interactive costumes; check out his Heartbeat Straitjacket and demo video.
Features:
Documents:
Replaces: COM-09259
Manufacturer
Responsible person
The inverter is powered by 12V DC, it generates alternating current to supply electroluminescent wires that glow under the influence of high voltage supply. Adafruit 832
No product available!
Adafruit 831 - EL Wire 6V Sound Activated Pocket Inverter
Adafruit 587 - EL wire starter pack - Red 2.5 meter (8.2 ft)
No product available!
Adafruit 584 - EL wire starter pack - Green 2.5 meter (8.2 ft)
No product available!
Adafruit 583 - EL wire starter pack - Blue 2.5 meter (8.2 ft)
No product available!
Adafruit 448 - 12V EL wire/tape inverter
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
No product available!
No product available!
MT41K512M16HA-125 is an 8Gb DDR3 DRAM that operates at up to 800MHz at a low voltage of 1.35V, ideal for systems requiring high bandwidth and energy efficiency. With a 512Mx16 organization and an operating temperature range of 0°C to 90°C, this memory offers fast data access and reliability in a variety of applications such as servers and industrial computers.
No product available!
5V / 3.1A eXtreme power supply with microUSB plug for all Raspberry Pi computers (including Pi 3 model B and Pi 3 model B +)
No product available!
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 25mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 9 x 9 x 4mm
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
No product available!
Kit: MAXimator, MAXimator Expander, ZL32PRG - USB Blaster PRO
No product available!
Power Supply 2.5A 5.1V for Raspberry Pi 3 model B - STONTRONICS T5875DV
No product available!
MYD-JA5D44 Development Board is a complete educational platform. Its heart is the MYIR MYC-JA5D44 module, which was equipped with the Atmel SAMA5D44 processor based on Cortex-A5 cores. The processor can work at a maximum frequency of 600 MHz. Min. RS232, RS485 connectors, HDMI connector, 3.5 mm Jack Audio inputs, microSD memory card slot, 10/100 Mbps Ethernet slot and many more.
No product available!
The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into three parts. DFR0385
No product available!
Flex Cable for Raspberry Pi Camera - 300mm / 12". Adafruit 1648
No product available!
Comes with a 6"x6" (152mm x 152mm) square of Pyralux. It\'s ED-Y type copper at 35um (1 oz/ft2) and has a polymide of 25um (1 mil). The thick copper layer means it can carry a lot of current, and its trivial to solder to it. Adafruit 1894
No product available!
Patchcord UTP 5E Ethernet cable with a length of 25 cm - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - gray, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 50 cm - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 1.5 m - black, with 2xRJ45 connectors
No product available!
COM-10878 - EL Escudo Dos