- Out-of-Stock
Digital altimeter Altimeter Explore
ID: 560104
Digital altimeter with barometer and temperature sensor, equipped with MPL3115A2 system with I2C interface. MOD-69
Description
The module is a digital, precise altimeter with a barometer and a temperature sensor. It has a built-in MPL3115A2 system (Freescale Semiconductor, Inc. *) with an I2C interface, enabling pressure measurement in the range from 20 kPa to 110 kPa. The measurement resolution is 20-bit for the altimeter and barometer, and 12-bit for the temperature sensor. The configuration jumper V_SEL +3,3 V / + 5 V enables selection of supply voltage and digital signals. Attention! The standard setting of the power jumper is +3.3 V.
Attention!
The standard setting of the power jumper is +3.3 V.
Modulowo® DuoNect ™ solution
The Modulowo® DuoNect ™ solution enables fast and easy connection of expansion modules to Arduino , Raspberry Pi , Intel® Edison , STM32 Nucleo , Atmel Xplained , TI LaunchPad , Freescale Freedom and other platforms.
properties
- Built-in MPL3115A2 system
- Compliance with Modulowo® DuoNectTM
- I2C interface
- Edge and lead leads with 2.54 mm pitch
- Additional outputs with a 2.0 mm grid
- Built-in signal translator +3.3 V / + 5V
- Space for the system to identify the module
- Supply voltage: + 3.3 V / + 5 V
- Dimensions: ~ 26 mm x 35 mm
- Compliance
Included
- Module MOD-69
- A set of connectors for self-assembly
To download
560104
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
No product available!
No product available!
No product available!
No product available!
No product available!
hb03w-p-000-00
Delivery date unknown
No product available!
No product available!
No product available!
Adafruit 2486 - NETduino 3 WiFi is an open source electronics platform using the .NET Micro Framework
Retired
No product available!
The Arduino M0 represents a simple, yet powerful, 32-bit extension of the Arduino UNO platform. The board is powered by Atmel’s SAMD21 MCU, featuring a 32-bit ARM Cortex® M0 core.
Retired
No product available!
Arduino Yun Mini is a breadboard PCB developed with ATmega 32u4 MCU and QCA MIPS 24K SoC CPU operating up to 400 MHz. Qualcomm Atheros CPU supports a Linux distribution based on OpenWRT named Linino. The board has built- in WiFi, supports 20 digital input/output pins, a 16 MHz crystal oscillator, a micro USB connector, an ICSP header, two reset buttons and one user button.
Retired
No product available!
The Arduino 4 Relays Shield allows your Arduino driving high power loads that cannot be controlled directly by Arduino\'s digital pins. The Shield features four relays, each relay with 2 pole changeover contacts (NO and NC). Four LEDs indicate the on/off state of each relay. (A000110)
Retired
No product available!
The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega
Retired
No product available!
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Retired
No product available!
The Arduino 9 Axes Motion Shield allows your Arduino to measure movement: orientation, acceleration and magnetic field. A000070
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Digital altimeter with barometer and temperature sensor, equipped with MPL3115A2 system with I2C interface. MOD-69