A 20x15 mm knob with an internal diameter of 6 mm. For mounting on a potentiometer or rotary encoder

2.7V to 5.5V Low Power  12-Bit Digital-To-Analog Converters With Internal Reference And Power Down, SOIC20, Texas Instruments, RoHS

Ethernet module with WIZ5500 chip and RJ45 connector. It allows you to connect the Feather series boards to a wired network. Adafruit 3201

A 20x15 mm knob with an internal diameter of 6 mm. For mounting on a potentiometer or rotary encoder

OV5647 Camera Board /w M12x0.5 mount Lens fully compatible with Raspberry Pi. ArduCAM B0031

TSV521ICT, High merit factor (1.15 MHz for 45 μA) CMOS op amps, SC70-5

Crowtail – Laser Pointer 2.0 generates a red laser beam of 650 nm with a power of 5 mW and is compatible with the Crowtail system. Used in educational projects, demonstrations, and research as a precise point indicator.

The CAN-BUS Arduino Shield v2.0 can be stacked on an Arduino UNO, Arduino Leonardo or Arduino MEGA board. The shield integrates an MCP2515 CAN-BUS chip on the shield and has a CAN-BUS transceiver function. With an on-board DB9 and CAN-BUS connector you can choose a suitable port according to your host device. There is also an integrated MicroSD socket for data storage. DFR0370

Module with a color IPS LCD display with a diagonal of 0.85" and a resolution of 128x128 pixels. It uses the GC9107 controller and communicates via the SPI interface. Waveshare 0.85inch LCD Module

Crowtail – 315MHz RF Receiver with Transmitter 2.0 is a simple set for one-way wireless communication in the 315 MHz band, intended for remote control, automation, and IoT projects. Easily integrated with Arduino systems via the Crowtail interface.

Module with a 1.5" color IPS LCD display and a resolution of 240x280 pixels. It has rounded corners and uses the NV303B controller (SPI interface). Waveshare 1.5inch LCD Module

Flexible RGB 8x8 LED Matrix Module with Addressable WS2812B LEDs. modFlexMatrix8x8

Finder 41.31.9.024.0010 is a high quality SPDT relay, operating at a coil voltage of 24V DC, capable of switching currents up to 12A at 250V AC on a single contact. Its compact design and PCB mount leads enable easy integration into automation, electronics and control systems, ensuring long-lasting and reliable operation.

A module for building a rear bicycle light using 1000 mCd red LEDs. Power supplied by AA batteries, which are not included in the kit. Kitronik 2106

AVR, 8kB Flash, 1kB RAM, 512B EEPROM, TQFP32, RoHS

Module with the PAM8904 controller designed specifically to control piezoelectric elements. The amplifier operates over a wide frequency range, up to 300 kHz, and allows for gain up to approximately 13 Vpp. Adafruit 5791

Module with a 1.44 "color liquid crystal display and 128 x 128 pixel resolution The display has a built-in ILI9163C driver. Thanks to the pin connector, the module can be easily attached to the contact plate or wires 1.44 \'SPI 128 * 128 V2.1

Long-range Sub-GHz wireless RF transmitter and receiver module, capable of operating in the 433 MHz frequency band. The integrated architecture allows the use of a minimum number of external components while maintaining maximum design flexibility. Hoperf RFM69HW-433S

Active USB 3.0 Hub with 4 ports and a phone holder. It allows you to extend the number of USB ports on your computer and connect multiple devices at the same time

Crowtail – Current Sensor 2.0 enables AC/DC current measurement up to ±20 A using the ACS712 chip and generates an analog signal for further analysis. Used in energy-consumption monitoring systems, automation, and laboratory measurements.