Category: Feather

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759

Development kit with nRF52840 microcontroller with ARM Cortex M4F core and BLE communication. Equipped with motion sensors, magnetometer, light, humidity, pressure sensors and a microphone. Adafruit 4516

Module with WiFi Espressif ESP32-S2. It integrates the TFT LCD display, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5300

CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709

Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147

Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. Adafruit 3405

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. Adafruit 3179

FeatherWing Doubler is a shield that allows you to create your own layout based on two or one Feather series. The plate has 256 holes, including designated, common solder points for supply voltages. Adafruit 2890

Data logger dedicated to Feather plates. Equipped with RTC clock, battery slot and micro SD card slot. Adafruit 2922

A module that allows you to create your own layout based on the Feather tile. Equipped with prototype holes and a set of screw connectors with pins out. Adafruit 2926

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

The board is equipped with a STM32F405 microcontroller with an ARM Cortex-M4 core and SPI Flash memory, GPIO pins, a connector for connecting a battery with a charging circuit and a STEMMA QT socket. Adafruit 4382

Adafruit Feather 32u4 RFM95 is a development board with built-in ATmega32u4 AVR microcontroller (8MHz, 32kB Flash, 2kB RAM) and RFM95W module enabling wireless communication in the 868 MHz or 915 MHz band. The board is compatible with Arduino IDE. Adafruit 3078

Module with WiFi Espressif ESP32-S2. It integrates two 3.3 V stabilizers, SPI Flash memory, LiPo charging circuit, light sensor and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4769

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895

Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323