Terminal Block Breakout - prototyping module for Feather

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Small development kit with ATmega32u4 microcontroller. The board has 6 power, 6 analog and 17 digital pins, which makes it have similar capabilities to the Arduino UNO. Compatible with Arduino. Adafruit 3675

Module with ATSAMD21G18 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The ATSAMD21G18 microcontroller (ARM Cortex-M0) is clocked at 48 MHz and operates at 3.3 V. Adafruit 3176

FeatherWing Proto - Prototyping Add-on For All Feather Boards

At the Feather 32u4\'s heart is ATmega32u4 clocked at 8 MHz and at 3.3V logic. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. Adafruit 2795

Module with WiFi Espressif ESP32-S2. It integrates two 3.3 V stabilizers, SPI Flash memory, LiPo charging circuit, light sensor and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4769

Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5323

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

Module with ATmega32u4 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The microcontroller is clocked at 8 MHz and works at 3.3 V. Adafruit 3076

Module with WiFi Espressif ESP32-S2. It integrates the TFT LCD display, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5300

Module with WiFi Espressif ESP32. It offers 8MB Flash, 2MB PSRAM, LiPo charging circuit and RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5438

A board with an RP2040 microcontroller and a LoRa RF95 module operating in the 868 MHz frequency band. It has a built-in LiPo charging circuit and STEMMA QT connector. Ideal for IoT projects. Adafruit 5714

Board with RP2040 microcontroller and HDMI video connector. Has a built-in LiPo charging circuit and STEMMA QT connector. Allows the use of the Feather module to display data on a monitor. Adafruit 5710

The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759