Categories

Kamami.pl - Official Raspberry Pi distributor

New products



Adafruit Feather M0 Bluefruit LE

Low-power, 2.4GHz spectrum wireless protocol that you can use with iOS without needing special certification. Supported by all modern smart phones - excellent for use in portable projects that will make use of an iOS or Android phone or tablet; it also is supported in Mac OS X and Windows 8+. Adafruit 2995

More details

ID: 560963

35,34€ gross (23% VAT)
28,73€ net

Add to wishlist

Data sheet

MicrocontrollerATSAMD21E18
CoreCortex-M0+
Frequency48MHz
Flash memory256kB
RAM32kB
EEPROM memorynone
Number of digital pins20
Number of PWM channels8
Ilość wejść analogowych10
ADC1x 12bit
DAC1x 10bit
CANnone
USB1
Ethernetnone
WiFi/BT moduleNo
Bluetooth moduleYes
GSM/GPRS moduleNie
Logic voltage3,3 V
MicroSD slotNo
Supply voltage min5 V
Supply voltages max5 V

More info

Description

Feather is the new development board from Adafruit, and like it's namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

This is the Adafruit Feather M0 Bluefruit - our take on an 'all-in-one' Cortex M0+ Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather M0 with a BTLE module, ready to rock!

Bluetooth Low Energy is the hottest new low-power, 2.4GHz spectrum wireless protocol. In particular, its the only wireless protocol that you can use with iOS without needing special certification and it's supported by all modern smart phones. This makes it excellent for use in portable projects that will make use of an iOS or Android phone or tablet. It also is supported in Mac OS X and Windows 8+

At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.

Features

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 5.7 grams
  • ATSAMD21G18 @ 48MHz with 3.3V logic/power
  • No EEPROM
  • 3.3V regulator with 500mA peak current output
  • USB native support, comes with USB bootloader and serial port debugging
  • You also get tons of pins - 20 GPIO pins
  • Hardware Serial, hardware I2C, hardware SPI support
  • 8 x PWM pins
  • 10 x analog inputs
  • 1 x analog output
  • Built in 100mA lipoly charger with charging status indicator LED
  • Pin #13 red LED for general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

Downloads

Manufacturer

Accessories