 
        
           
        
          Module of 16-channel expander of I/O ports controlled by the I2C interface. It was based on the Microchip MCP23017 chip. Each IO pin can be configured as input or output. The maximum output current should not exceed 25 mA, and the pins are compatible with voltages of 3.3 V and 5 V. The module has 3 address jumpers that allow you to select 8 different addresses, so you can connect up to 8 modules to one I2C interface. Communication takes place via the I2C interface (STEMMA QT connector).
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
 No product available!
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Flexible 4-core cable, 50 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17260
 No product available!
Module with 8 digital inputs and 4 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8024ADAM
16-channel I/O port expander module controlled by the I2C interface. The module is based on the MCP23017-E/SS system.
4-channel PCIe port expander. It can be powered with 12 V via a PCIe connector or an external DC connector. Waveshare PCIe-Packet-Switch-4P
An 4-channel I2C expander module, which is based on the TCA9546A chip. It allows connecting several devices with the same address to a single I2C interface. Adafruit 5664
16-channel PoE GPI/GPO module enabling connection of a PC to other electronic circuits via a network. It does not need a separate cable for power and data transmission. It can be controlled via a simple web interface or Telnet. Numato Lab NLGP1001-A
 No product available!
DAQ device based on Ethernet communication and equipped with 24 digital inputs/outputs and a counter input. It allows you to control devices via the Internet. Digilent 6069-410-052
 No product available!
Module with 16 digital inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8026ADAM
16-channel GPIO expander with an I2C interface microcontroller can interface with 16 fully configurable digital input/output pins. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. With a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix. BOB-13601
 No product available!
KAmod I2C Hub4 enables splitting the I2C bus into four independent outputs with a voltage level translation function, eliminating address conflicts and increasing connection flexibility. The module is intended for projects with multiple I2C devices requiring separation or diverse supply voltages.
8-channel solenoid driver controlled via I2C. Compatible with 3V/5V logic, features STEMMA QT / Qwiic connectors. Adafruit 6318
Module with 8-channel PCF8574 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5545
Module with 4 digital inputs, 4 outputs and 6 analog inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP9039ADAM
Module with 32 IO pins and 14 analog inputs. It communicates via the RS485, USB or Ethernet interface and supports the Modbus RTU/TCP protocol. Numato Lab NLGM1002-A
 No product available!
Module with 4 digital inputs and 4 digital outputs. It communicates via RS485 interface and supports Modbus RTU protocol. The board is enclosed in an industrial enclosure. MA01-AXCX4040
128-channel IO expander with 32 analog inputs. It communicates via the USB interface. Numato Lab GP1280001
 No product available!
The KAmod I2C-IOexp16 module is an extension equipped with 16 programmable digital lines (inputs or outputs), based on the MCP23017 system and controlled via the I2C bus with the possibility of connecting up to 8 modules thanks to addressing. The module works with a voltage from 2 to 5 V, has an interrupt output and allows for a current flow of up to 20 mA on each line
 
                    Module with 16-channel IO expander MCP23017 controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5346