8-channel expander module of I/O ports controlled by the I2C interface. It is based on the PCF8574 chip which has no pin direction register and you cannot set pins as input or output - instead each pin has two possible states. The maximum output current should not exceed 20 mA, and the pins are compatible with voltages of 3.3 V and 5 V. The module has 3 address jumpers that allow you to select 8 different addresses, so you can connect up to 8 modules to one I2C interface. Communication takes place via the I2C interface (STEMMA QT connector). Full documentation is available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
No product available!
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
No product available!
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
No product available!
Cable with a length of 150 mm, on one side terminated with a female STEMMA QT (Qwiic) connector, and on the other side with single female goldpin connectors. Adafruit 4397
No product available!
Cable with a length of 150 mm, on one side terminated with a female STEMMA QT (Qwiic) connector, and on the other side with single male goldpin connectors. Adafruit 4209
4-pin cable with JST SH connector compliant with STEMMA QT/Qwiic. Ended with alligator clips. Adafruit 4398
Module with 16-channel IO expander MCP23017 controlled by the I2C interface. Designed for minicomputers Raspberry Pi. Adafruit 4132
8-channel I2C expander module based on the TCA9548A system. The module has Qwiic connectors and allows communication with many I2C devices that have the same address. Sparkfun BOB-16784
16-channel I/O port expander module controlled by the I2C interface. The module is based on the MCP23017-E/SS system.
Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047
IO port expander for M5Stack kits. Equipped with 8 IO pins and power pins, it communicates via the I2C interface. M5Stack U011-B
Module with IO expander equipped with 14 inputs/outputs, including 8 connected to the ADC converter and 6 to PWM outputs. It communicates via the I2C interface and is compatible with the Raspberry Pi. Pimoroni PIM517
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
I2C bus amplifier module based on the LTC4311 system. It enables communication via a popular interface over much longer distances while maintaining high transmission speeds. Adafruit 4756
Adapter dedicated to the Nintendo Wii Nunchuck. It allows you to connect the controller to the development board via the I2C interface. Adafruit 4836
Module with 16-channel I/O ports expander controlled by the I2C interface. It was based on the MCP23017 chip
Module with 16-channel IO expander MCP23017 controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5346
4-channel PCIe port expander. It can be powered with 12 V via a PCIe connector or an external DC connector. Waveshare PCIe-Packet-Switch-4P
Module with a 16-channel GPIO expander with the ability to control LEDs. It communicates via the I2C interface. Waveshare AW9523B IO Expansion Board
128-channel IO expander with 32 analog inputs. It communicates via the USB interface. Numato Lab GP1280001
No product available!
16-channel IO expander with 10 analog inputs. The board communicates via the Ethernet interface. Numato Lab GPETH160001
Module with 8-channel PCF8574 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5545