Best sellers

150W electronic load module with active cooling by a fan. Equipped with a color display and the ability to view parameters on a PC and mobile devices via Bluetooth. modLOAD150W

Finder 22.21.9.024.4000 is a modular installation relay equipped with one normally open (NO) contact with a 20 A load capacity at 250 V AC. Powered by a 24 V DC coil voltage, it is designed for DIN rail mounting, facilitating easy integration into industrial automation systems.

Multifunctional tool for crimping connectors for AWG 1.5 / 2.5 / 6.0 wire and for removing insulation from wires 0.75 / 1.0 / 1.5 / 2.5 / 4.0 / 6.0mm. HY-033

Panel thermometer with LCD display with measuring range inside -10-50 ° C and outside -50 ~ 70 ° C. 50-310

FDC6420C; MOSFET N / P transistor; SSOT-6, Fairchild / On Semiconductor

Module with the ATMega4809 microcontroller from the AVR family (48 KB Flash, 6 KB SRAM, 256 B EEPROM). The module has two 15-pin connectors equipped with GPIO, SPI, I2C, PWM, USART, DAC and ADC. Arduino ABX00028

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

A professional tool for crimping 10p10c telephone plugs. Solidly made, simple and convenient to use, it allows you to cut and remove insulation. HT-2092C

A programming and robotics learning kit that lets you build a micro:bit-controlled robotic buggy. It is equipped with two DC motors, ultrasonic sensors to detect obstacles, and programmable LEDs. Powered by four AA batteries, the kit can be programmed in the Microsoft MakeCode or MicroPython environment, making it a great solution for beginners and more advanced users. Kitronik 5683

Durable 0.8 mm hardened steel hotend, compatible with Bambu Lab P1 and X1 printers, ideal for working with abrasive filaments. Bambu Lab Hotend P1/X1 0.8mm Complete Hotend / Hardened Steel

Flexible cable (tape) 50 cm long, used to connect the camera module with Raspberry Pi computers. The tape has 15 wires and a pitch of 1mm

Safety system for two Li-Ion cells with 11.1V. The module has the function of charging cells with the balancer, discharging and the function of protecting the cells against discharge. Cells can be charged with continuous current up to 20A and discharged with current 40A. modBMS40A

Multifunctional tool for clamping connectors and coaxial connectors RG58, RG6, RG174, has a locking function and the ability to adjust the pressure. HT-301B

NUCLEO series starter kit equipped with STM32G474RE microcontroller (512 kB Flash, Cortex-M4), with built-in programmer-debugger ST-Link-V3E, equipped with connectors compatible with Arduino.

The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03

Multifunctional tool for crimping connectors and coaxial connectors RG58, RG59, RG62, RG6, has a locking function and the ability to adjust the pressure. HT-301C

32-bit microcontroller from the STM32G4 family with ARM Cortex-M4 core, 128kB Flash memory, 32kB RAM memory, clock speed up to 170MHz and I2C, SPI, UART/USART, LIN, IrDA, I2S, DMA, PWM, Temp Sensor, WDT interfaces, A/D 10x12b in an LQFP32 enclosure. STMicroelectronics STM32G431KBT6

GL5528, Photoconductive cells 10-20 kOhm, 5 mm

Finder 11.41.8.230.0000 is a twilight switch relay designed for DIN rail mounting, powered by 230 V AC. It features a single-pole double-throw (SPDT) contact with a 16 A load capacity at 250 V AC, allowing for automatic lighting control based on the ambient light intensity.

Bambu Lab AMS Hub allows you to connect up to four AMS modules to one Bambu Lab 3D printer, allowing you to support up to 16 filaments. The device provides stable communication via the CAN interface and automates material management, which is useful for multi-material projects and fast color switching