Magnetic Encoder Pair Kit for Mini Plastic Gearmotors, 12 CPR, 2.7-18V
ID: 562589
5906623485970
zł36.59
Tax included
zł29.75 tax excl.
The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. This module is compatible with all of the Pololu dual-shaft mini plastic gearmotors. Pololu 1523
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. This module is compatible with all of the dual-shaft mini plastic gearmotors we carry. This kit includes two dual-channel Hall effect sensor boards and two 6-pole magnetic discs that can be used to add quadrature encoding to two mini plastic gearmotors with extended back shafts (motors are not included with this kit). The encoder board senses the rotation of the magnetic disc and provides a resolution of 12 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output shaft, multiply the gear ratio by 12.
This compact encoder solution fits within the 11.5 mm × 22.5 mm cross section of the rear of the motors on three of the four sides. The fourth side of the encoder has the signal and power connections, and it extends 5 mm past the edge of the motor to leave room for mounting brackets. The assembly does not extend past the end of the extended motor shaft, which protrudes 5 mm beyond the back of the motor.
Notes This sensor system is intended for users comfortable with the physical encoder installation. It only works with mini plastic gearmotors that have extended motor shafts. The assembled encoder will extend 5 mm beyond the back of the motor (it fits entirely within the length of the extended motor shaft).
Weight of full set. Each encoder board weighs ~0.6 g and each magnet disc weighs ~0.6 g.
Weight of full set. Each encoder board weighs ~0.6 g and each magnet disc weighs ~0.6 g.
Features
- Size: 20 mm × 16.5 mm1
- Weight: 2.4 g2
- Minimum operating voltage: 2.7 V
- Maximum operating voltage: 18 V
- PCB dev codes: enc04a
- Other PCB markings: 0J9719
562589
You might also like
This compact, inexpensive plastic gearmotor (high-power brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Delivery date unknown
No product available!
This compact, inexpensive plastic gearmotor (high-power brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
zł31.81
24h
Available quantity: 1
Available
Other products in the same category (15)
A set of two optical quadrature encoders for Polol micromotors with a two-sided extended shaft, compatible with the LP, MP, and HP series, 5V power supply. Polol 2590
zł59.91
6 weeks
No product available!
Set of two magnetic encoders for use with micro motors. Regular mounting, set of 2. Pimoroni PIM604
zł47.97
24h
Available quantity: 5
Available
This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the chassis travels. ROB-12629
zł92.16
4 weeks
No product available!
AB two-phase pulse wave, measured by two infrared reflective sensor. These two sensor pulse waveform is close to a phase difference of 90 degrees, through the AB two-phase lead and lag of the waveform judged wheel forward rotation or the reverse. SEN0116
zł23.23
24h
Available quantity: 3
Available
Add quadrature encoders to your 20D mm metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and Hall effect sensors to provide 20 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit.
zł42.14
24h
Available quantity: 6
Available
A set of two magnetic encoders for use with Pololu DC Micro motors. The maximum resolution is 12 pulses per one revolution of the motor shaft. Powered from 2.7V to 18V. Pololu 4760
zł31.89
24h
Available quantity: 4
Available
This encoders are designed for DFRobot 3PA and AWD Rovers. It can give you the rotation degree of the wheels. Encoder uses non-contact method to convert the angular displacement signals. Best fit with Micro DC Geared Motor. SEN0038
zł59.96
24h
Available quantity: 2
Available
Set of two magnetic encoders for use with micro motors. Side mounting, set of 2. Pimoroni PIM605
zł35.26
24h
Available quantity: 6
Available
A set of magnetic encoders for the Romi Chassis chassis. With their help, we can measure the distance traveled by our mobile robot or control the engine speed. Pololu 3542
zł45.93
6 weeks
No product available!
The kit uses a magnetic disc and hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. Compatible with all of the dual-shaft micro metal gearmotors we carry, including the HPCB versions. Pololu 3081
zł39.37
24h
Available quantity: 4
Available
Pololu - 1524
zł3.75
24h
Available quantity: 4
Available
Magnetic disk for use with magnetic encoders designed for Pololu 20D series motors. It allows you to generate 12 pulses per revolution. Pololu 3449
zł3.90
24h
Available quantity: 5
Available
Pololu - 3498
zł4.17
24h
Available quantity: 5
Available
A set of two magnetic encoders for use with Pololu DC Micro motors. The maximum resolution is 12 pulses per one revolution of the motor shaft. Powered from 2.7V to 18V. Pololu 4761
zł40.42
24h
Available quantity: 1
Available
Encoder for Pololu Wheel 42x19mm
zł66.64
24h
Available quantity: 1
Available
The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit. This module is compatible with all of the Pololu dual-shaft mini plastic gearmotors. Pololu 1523