![Analog MEMS Microphone Breakout - ICS-40180 analog microphone module Analog MEMS Microphone Breakout - ICS-40180 analog microphone module](https://kamami.pl/42575-large_default/analog-mems-microphone-breakout-ics-40180-analog-microphone-module.jpg)
![Analog MEMS Microphone Breakout - ICS-40180 analog microphone module Analog MEMS Microphone Breakout - ICS-40180 analog microphone module](https://kamami.pl/42575-large_default/analog-mems-microphone-breakout-ics-40180-analog-microphone-module.jpg)
zł28.16 tax excl.
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-18011
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Module with analog MEMS ICS-40180 microphone and amplifier, which allows direct connection to the ADC converter on the microcontroller. The microphone used is omni-directional, which means that it is good at picking up sound sources from all directions. The microphone port is located on the bottom of the board, so keep this in mind when installing the module in the project. The sensor will allow you to add sound to the application, it will allow you to detect voice, clap or slam the door. Full documentation with examples of use is available in the guide.
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Cables for evaluation boards, set of 10 pcs., blue colour
Cables for evaluation boards, set of 10 pcs., red colour
Cables for evaluation boards, set of 10 pcs., green colour
A set of 10 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-10-17)
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
Module with a sound sensor based on an electret microphone and LM358 amplifier. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020023
The VM-CLAP1 Hand Clap Sensor from Verbal Machines is a low-power, microprocessor-based audio sensor that can detect hand claps or finger snaps while ignoring background noises such as human speech or music. Pololu 2580
MEMS SPM1423 digital microphone module with PDM modulation. It communicates via the I2S interface. M5Stack U089
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
A module with an electret microphone and amplifier that will allow you to detect voice, clap, slam doors and other sounds using an analog or digital output. SparkFun SEN-12642
No product available!
A volume sensor designed to detect loud ambient sounds. The module uses a microphone and LM2904 amplifier. The output value (analog signal) depends on the volume of the detected sound. In order to eliminate interference, the microphone signal is subjected to double filtering. Seeed studio 101020063
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-19389
Expansion board compatible with STM32 Nucleo. Allows you to prototype solutions with digital microphones. STMicroelectronics X-NUCLEO-CCA02M2
A module with an electret microphone and MAX9812 amplifier, which will allow you to detect a voice, a clap or a door slam. Has an analog output
MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
Module with WM8960 audio decoder that allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Adafruit 4757
Audio module with two microphones and display designed to work with the Raspberry Pi. Pimoroni PIM524
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-18011