Bambu Lab Desiccant for AMS(6 pack)
ID: 1192586
6977252428873
zł32.48
Tax included
zł26.41 tax excl.
Bambu Lab moisture absorber, containing calcium chloride, provides effective protection of the filaments against moisture, guaranteeing the highest quality of 3D prints by eliminating problems related to air bubbles. Bambu Lab Desiccant for AMS
Description
The Bambu Lab moisture absorber was designed for use in the intelligent Bambu Lab AMS automatic filament feeding and switching system. The product contains six bags of calcium chloride with hygroscopic properties, able to effectively absorb moisture from the environment. Each bag has dimensions of 100x45x17 mm and weighs 20 g. The use of Bambu Lab moisture absorbers guarantees the highest quality of filaments and protects 3D prints against losses caused by air bubbles.
In the AMS system, the Bambu Lab moisture absorber is located next to the filament support rollers. There are two dehumidifier chambers secured with a plastic mesh. To replace the desiccant, open each compartment, remove the used desiccant and replace it with a new bag. After replacement, it is important to close the AMS to prevent moisture from being absorbed from the outside.
The new absorbent bag contains white calcium chloride in loose form. As moisture is absorbed, this substance turns into a yellow paste. When the calcium chloride has completely turned into a yellow paste, it has absorbed the maximum amount of moisture and needs to be replaced. If the absorber is worn out, it is recommended to dry the filament spools before replacing them with new packaging.
1192586
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Self-adhesive kapton tape 150mm wide, made of polyimide, protects electronic components from high temperatures. It is also used during 3D printing
zł128.12
24h
Available quantity: 4
Available
Self-adhesive kapton tape with a width of 200mm, made of polyimide, protects electronic components from high temperatures. It is also used during 3D printing
zł144.71
24h
Available quantity: 7
Available
Solvent HIPS is a preparation for dissolving supporting structures made of HIPS filament used in 3D printing, used in metal containers or ultrasonic baths, with a dissolution time of 1 to 24 hours, which does not require heating. MICRO CHIP ELEKTRONIC MCP ART.050
zł45.90
24h
Available quantity: 14
Available
Solvent HIPS is a preparation for dissolving HIPS filament support structures used in 3D printing, used in metal containers or ultrasonic baths, with a dissolving time from 1 to 24 hours, which does not require heating. MCP ART.051
zł69.86
24h
Available quantity: 4
Available
Feeler gauge consisting of 17 blades with a thickness of 0.02 to 1 mm. It will work, among others for leveling the table in a 3D printer. Yato YT-7220
zł7.33
24h
Available quantity: 11
Available
Magnetic sheet with adhesive is a practical and universal solution for attaching various objects to magnetic surfaces
zł69.90
24h
Available quantity: 1
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł6.20
24h
Available quantity: 10
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł6.69
24h
Available quantity: 4
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł5.44
24h
Available quantity: 1
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł5.29
4 weeks
No product available!
A stand supporting the filament spool during 3D printing. The filament is moved thanks to metal rollers that ensure even development of the filament, and silicone anti-slip pads guarantee excellent grip.
zł19.78
4 weeks
No product available!
SFS V2.0 is a precision photoelectric filament sensor by Bigtreetech, designed for monitoring the 3D printing process. This sensor significantly enhances print control, helping to avoid issues such as clogged nozzles, filament running out, or extruder problems. With advanced features like an LED status indicator and bi-directional feeding, the SFS V2.0 becomes an invaluable tool in any 3D printing workshop. BigtreetechSFS V2.0
zł53.28
4 weeks
No product available!
Bambu Lab moisture absorber, containing calcium chloride, provides effective protection of the filaments against moisture, guaranteeing the highest quality of 3D prints by eliminating problems related to air bubbles. Bambu Lab Desiccant for AMS
zł32.48
24h
Available quantity: 60
Available
Bambu Lab AMS Hub allows you to connect up to four AMS modules to one Bambu Lab 3D printer, allowing you to support up to 16 filaments. The device provides stable communication via the CAN interface and automates material management, which is useful for multi-material projects and fast color switching
zł273.23
2 weeks
No product available!
0.3 x 70 mm cleaning needles are precision tools for removing dirt and filament residue from 3D printer nozzles, improving print quality and extending the life of the device. Made of durable stainless steel, they guarantee safe cleaning of small diameter nozzles without the risk of damage.
zł9.98
2 weeks
No product available!
The 0.3 x 75mm cleaning needles are precision tools for removing filament residue from 3D printer nozzles, made of durable stainless steel. With a length of 75mm, they provide better access to hard-to-reach places, and the package contains 15 pieces, which guarantees long use.
zł19.96
Delivery date unknown
No product available!
Bambu Lab moisture absorber, containing calcium chloride, provides effective protection of the filaments against moisture, guaranteeing the highest quality of 3D prints by eliminating problems related to air bubbles. Bambu Lab Desiccant for AMS