- Out-of-Stock
AVT2796 A +
ID: 190665
UNUSUAL CURED CASTLE - PLATE AND PROGRAMMED LAYOUT
UNUSUAL CURED CASTLE - PLATE AND PROGRAMMED LAYOUT
Producer: AVT
It is well known that thieves have access to factory alarm and code devices. That is why non-standard solutions are particularly valuable. A typical combination lock with a combination of four digits has ten thousand possible settings. It's easy to see the code entered and push the door.
Although the presented device has only one thousand four hundred and forty combinations, the code changes every minute and only the user knows to what extent the changes have taken place. If the code is entered incorrectly three times, the lock will be blocked for a few minutes.
It is worth mentioning that the lock code depends on the current time shown by the device.
The device is especially recommended where there is a need to control access to selected zones
Selected parameters:
- dynamic change of access codes
- sound and light signaling of the work status
- four-digit LED display
- control element - relay
- locking the lock after three wrong entries of the access code
- built-in clock arrangement with support
- current time display
- power supply - 6-12 Vdc, backup - lithium battery
- in the set, printed circuit boards, programmed layout and documentation
- Detailed description in
Download
190665
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Xmega eXploreGO module with ATXmega128A4U microcontroller (version without MP3). The module is equipped with in DataFlash memory, microSD card connector. MOD-20 / AZ
Retired
No product available!
MOD-21.Z - push button module with bistable operation. The sensor operates based on the AT42QT1012 system.
Retired
No product available!
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
Retired
No product available!
No product available!
MOD-25.Z - touch sensitive button module with monostable function. The sensor operates based on the AT42QT1011 system.
Retired
No product available!
No product available!
No product available!
The module enables connection of two devices with I2C interface working with different voltage levels. MOD-28.Z
Retired
No product available!
It is used to monitor the temperature measurement and other parameters. The expansion module has an I2C / 1-Wire converter (DS2482) through which DS18B20 temperature sensors can be connected using two or three wires. MOD-29.Z
Retired
No product available!
Power module with IRFR4105Z transistor (MOD-30.Z), maximum current 2A, 5V power supply or 5V - 12V range (selection by jumper)
Retired
No product available!
The module with the DS18B20 sensor is used to measure the temperature in the range from -55° C to + 125° C, with an accuracy of +/- 0.5° C in the range from -10° C to + 85° C. The module communicates via the 1-Wire interface, thanks to which it can be connected using 2 or 3 wires - depending on the configuration. Temperature measurement can be performed with an accuracy of 9 to 12 bits. MOD-31.Z
Retired
No product available!
Universal module with LM358 operational amplifier. Depending on the additional elements installed, the amplifier can be freely configured, eg as a reversing, non-inverting amplifier, voltage follower or an integrating amplifier. MOD-32.Z
Retired
No product available!
No product available!
The modally controlled modulation module MOD-34 / BZ allows wireless load control with a current consumption of up to 10A via a relay. Includes wireless module nRF24l01.
Retired
No product available!
No product available!
No product available!
UNUSUAL CURED CASTLE - PLATE AND PROGRAMMED LAYOUT