K2622

Vision Edge computing platform with ARM Cortex-A53 1.2 GHz 64-bit quad-core processor, ARM Cortex-R5 600 MHz dual-core processor, embedded Mali400 graphics processor and FPGA chip. MYIR VECP Starter Kit

The minicomputer with the Intel Celeron J4115 quad-core processor (2.5 GHz, 64-bit) has 2 slots for DDR4 RAM modules. Additionally, it is equipped with, among others: Gigabit Ethernet, HDMI 2.0 port and Display Port 1.2 4K/60Hz, four USB sockets, 24 GPIO, PCI-e slot, two SATA3 connectors. Rev-B+. ODROID H2+

LPCXpresso55S16 evaluation kit with LPC55S16 microcontroller with ARM Cortex-M33 core. The board contains built-in LPC-Link2, audio subsystem, accelerometer, USB interfaces and Arduino connectors. NXP LPC55S16-EVK

The MIMXRT1062DVL6A Processor Evaluation Kit, which runs up to 600 MHz, has 256 MB of SDRAM, 512 MB of Flash and 64 QSPI Flash. NXP MIMXRT1060-EVK

Starter kit with the Kinetis K32 L2B microcontroller, integrated with the OpenSDA programmer-debugger, LCD display, accelerometer and MEMS magnetometer and USB connector. Conclusions compatible with Arduino. NXP FRDM-K32L2B3

Wired mouse with a precise optical sensor. It has a button to change the resolution in four levels: 800/1200/1600/2400 DPI. 1.8m cable with USB plug. Natec NMY-0667

Kit with LS1046A Freeway development board equipped with 4-core LS1046A processor, 4 GB RAM, 4GB Flash, 4 Gigabit Ethernet connectors, 2 USB 3.0 connectors, microSD slot and two M.2 slots. NXP FRWY-LS1046A-AC

Adapter for connecting a Raspberry Pi to the OM-SE050ARD development board. It allows you to run the EdgeLock SE050 application on a Raspberry Pi. NXP OM-SE050RPI

LPC55S69JEV98K, ARM Cortex-M33 Microcontroller, 32 bit, 150 MHz, 640 KB Flash, VFBGA98

USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)

Set with HQ camera, HDMI adapter, lens, tripod and Jetvariety adapter. Kit designed for NVIDIA Jetson Nano. ArduCAM B0243

A minisumo robot on a tracked chassis with Pololu 100:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3127

A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111

A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 2 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 2GB

White case for the NanoPi NEO3 minicomputer. It allows easy access to the Ethernet connector, USB, microSD cards and the power connector. FriendlyELEC Case for NEO3

HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. Auvidea 70511