- Out-of-Stock
These six-pin housings work with our wires with pre-crimped terminals to let you quickly make custom cables that mate with various 0.1"-spaced connectors, including male or female headers and solderless breadboards. They are sold in packs of 10.
These housings work with our wires with pre-crimped terminals and our crimp pins to let you quickly make custom cables that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!).
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other; you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy:
|
|
![]() |
![]() |
| Pins | A (mm) | B (mm) |
|---|---|---|
| 1×1 | – | 2.54 |
| 1×2 | 2.54 | 5.08 |
| 1×3 | 5.08 | 7.62 |
| 1×4 | 7.62 | 10.16 |
| 1×5 | 10.16 | 12.70 |
| 1×6 | 12.70 | 15.24 |
| 1×7 | 15.24 | 17.78 |
| 1×8 | 17.78 | 20.32 |
| 1×9 | 20.32 | 22.86 |
| 1×10 | 22.86 | 25.40 |
| 1×12 | 27.94 | 30.48 |
| 1×16 | 38.10 | 40.64 |
| 2×2 | 2.54 | 5.08 |
| 2×3 | 5.08 | 7.62 |
| 2×4 | 7.62 | 10.16 |
| 2×5 | 10.16 | 12.70 |
| 2×6 | 12.70 | 15.24 |
| 2×7 | 15.24 | 17.78 |
| 2×8 | 17.78 | 20.32 |
| 2×10 | 22.86 | 25.40 |
| 2×16 | 38.10 | 40.64 |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x4-Pin 10-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
The second version of the clock synchronization signal receiver, transmitted with AM modulation (DCF77). The built-in MAS6180 system allows you to receive timing frames from a time pattern using a carrier frequency of 77.5 kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77 v2
No product available!
No product available!
A circuit board for an adjustable power supply for contact plates. AVT1990 A
No product available!
No product available!
The RoboClaw motor controllers from Ion Motion Control (formerly Orion Robotics) can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual quadrature decoders make it easy to create a closed-loop speed control system. This version can supply a continuous 30 A per channel (60 A peak). Pololu 2396
No product available!
Rechargeable NiMH Battery Pack: 8.4 V, 900 mAh, 4+3 AAA Cells, JR Connector
No product available!
No product available!
RFID antenna designed for UHF RFID tags. It allows you to increase the effective range of tags to about 2.5 cm. SparkFun SPX-15113
No product available!
No product available!
Tamiya 70106 4-Channel Remote Control Box
No product available!
No product available!
This is an aluminum heat-sink for the Banana Pi RAM Chips. Run cool RAM chips with this little add-on. Just one heat-sink is needed to cover both RAM chips, use the picture below as reference. Signs of RAM or CPU overheating are computer stops responding, frozen screen and power shutt down or cycling.
No product available!
No product available!
No product available!
PCB and programmed circuit for the 230V switch controlled by any infrared remote control. AVT1840 A +
No product available!