- Out-of-Stock
These premium wires are stranded 26AWG wires with male terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 6" (15 cm) wires includes five each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
Manufacturer
Responsible person
Base plate for Trenz Electronics modules 4 x 5 cm, eg for TE0741. The board allows connecting to the module interfaces: USB, Ethernet, JTAG, UART. TE0703-06
No product available!
The expansion module with 6 Grove connectors for the micro:bit educational module. Seeed Studio 114991848
No product available!
A set for building a smartwatch based on the micro:bit educational module. It consists of an expansion board and a strap. Seeed Studio 114991969
No product available!
Silicone case designed for the micro:bit educational module. Blue color. Seeed Studio 114991668
No product available!
Minicomputer with Allwinner H2+ ARM Cortex-A7 4-core processor, Mali 400 MP2 GPU graphics card, 512 MB RAM, 8 GB eMMC, WiFi, BT 4.0 and numerous connectors. Banana Pi BPI-P2 Zero
No product available!
3D stereo camera module, which was built of two cameras with Sony IMX219 sensor and IMU ICM20948 sensor. Designed to work with Jetson Nano and Xavier NX. Seeed Studio 114992270
No product available!
20-pin straight goldpin female connector with a pitch of 2 mm. For THT mounting. PB20S_2.00mm
No product available!
Minicomputer with Allwinner H3 quad-core processor and 512 MB RAM. It has a WiFi and BT module, two Ethernet ports, 2 USB 2.0 ports and a microUSB and a microSD slot. FriendlyELEC NanoPi R1
No product available!
Minicomputer with Allwinner H3 quad-core processor and 1 GB RAM. It has a WiFi and BT module, two Ethernet ports, 2 USB 2.0 ports and a microUSB and a microSD slot. FriendlyELEC NanoPi R1
No product available!
Metal case for NanoPi R1 minicomputer. The set includes an external WiFi antenna
No product available!
Kit with Raspberry Pi computer built into the keyboard. Equipped with a power supply, mouse, HDMI cable and 16 GB microSD card. Raspberry Pi 400 Personal Computer Kits UK
No product available!
A set for building a smartwatch based on the micro: bit educational module. It consists of an expansion board and a strap and micro:bit module
No product available!
Expansion board with LTE Cat-1/GSM/GPRS module designed to work with Raspberry Pi minicomputers. Waveshare A7600E Cat-1/GSM/GPRS HAT
No product available!
Module with black and white e-Paper display, diagonal 7.8" and resolution 1872x1404 px. HDMI interface. Waveshare 7.8inch e-Paper
No product available!
3DR Radio is a set that allows bidirectional transmission of telemetry data, eg between the RC model (with the APM controller) and a PC. Light and small device in a set with antennas and connecting cables. Radio modules have a power of 100mW (+ 20dBm) and transmit a signal over a distance of 1km.
No product available!
Starter kit containing Raspberry Pi 4B 2 GB and all necessary accessories: 32 GB microSD memory card with Rasberry Pi OS system, Ethernet cable, official accessories: housing, cooling kit, power supply and HDMI cable and ruler
No product available!