- Out-of-Stock
These premium wires are stranded 22AWG wires with female terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 60" (150 cm) wires includes one each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Evaluation board with high voltage SMPS ALTAIR05T-800 SMPS switch / controller. The board is equipped with a 5W (5V / 1A) power charger with a wide voltage range and constant current. STMicroelectronics EVLALTAIR05T-5W
No product available!
No product available!
No product available!
AVT kit for self-assembly of a digital thermostat. AVT5441 B
No product available!
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Glitter Graphite
No product available!
Digital ECHO effect for use in audio systems. MK182
No product available!
Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981
No product available!
A module with a spectrum sensor that operates in the visible light range (450-650 nm). It allows you to measure and characterize a light source or check how the tested surface absorbs or reflects light at specific wavelengths. Pimoroni PIM412
No product available!
Bowden type extruder designed for 3D printers including the Ender 3 and Creality CR10, among others. It has high quality gears to ensure the filament is moved with confidence and precision. Trianglelab RNC Nano
No product available!
high-current XT60 connectors commonly used in the RC hobby industry. They are sold as matching male-female pairs and are great for projects that involve bigger motors and controllers, such as our high-power motor drivers and Simple Motor Controllers. Pololu 2174
No product available!
No product available!
Switch-mode power supply (constant voltage) with an output voltage of 12 V and a maximum current of 1.5 A. The cable terminated with a DC 5.5x2.5 plug
No product available!
No product available!
No product available!
No product available!