- Out-of-Stock

These premium wires are stranded 22AWG wires with female terminals on one end and male terminals on the other end. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 60" (150 cm) wires includes one each of ten different colors.
![]() |
0.1" connector custom cable. |
---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
0.1" connector custom motor cable. |
---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
length | monochromatic pack quantity | rainbow pack quantity |
---|---|---|
3" | – | 50 (5 of each color) |
6" | 10 | 50 (5 of each color) |
12" | 10 | 50 (5 of each color) |
24" | 5 | 50 (5 of each color) |
36" | 5 | 20 (2 of each color) |
60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
Female crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
Male crimp pin for 0.1" housings crimped onto a wire. |
---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Embedded Vision Bundle is the ideal tool for testing, developing and learning the design of embedded vision systems. The kit includes a ZYBO Z7-20 plate with Soil Xilinx Zynq-7000, a Pcam 5C camera module and a 15-wire FFC connection cable. Digilent 471-020
No product available!
Printed circuit board and programmed circuit for unipolar stepper motor driver. AVT1985 A +
No product available!
Orange Pi 2 is a computer with SoC Alwinner H3 (4 cores Cortex-A7, Mali400MP2 GPU), 1 GB RAM, 100 Mb Ethernet, WiFi 802.11 b / g / n. There are 4 USB 2.0 ports, a USB OTG port, a GPIO 2x20 connector compatible with Raspberry Pi 2 and a micro-SD card slot.
No product available!
No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and output on pads. It enables powering devices with 9 V or 12 V and testing chargers. PDC005
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
HK Turnigy nano-tech 6000mah 2S2P 65~130C Hardcase Lipo Pack (17265)
No product available!
The GPIO Expander board allows you to extend the project with an additional 16 I / O signal lines, equipped with an MCP23017 chip with an I2C interface. MOD-67
No product available!