- Out-of-Stock
AVT571 A +
ID: 193811
PROGRAMMED REMOTE CONTROLLER - PLATEBOARD AND PROGRAMMED LAYOUT
PROGRAMMED REMOTE CONTROLLER - PLATEBOARD AND CONTROLLED LAYOUT
Producer: AVT
The receiver allows reception and decoding of any signal from pilots working in RC5 and SIRC systems. Depending on the received code, the status of the receiver's outputs changes. You can assign a different control code to each of them. Depending on the needs, the change of the output state can be made with one key or two. An additional possibility is to switch the output status to the opposite one after receiving the programmed sequence.
The article describing the kit presents exemplary solutions of executive modules.
The device is especially recommended for the constructors of remote control systems
Selected parameters:
- sending infrared commands
- number of receiver outputs - 2
- command programming mode
- small dimensions
- power supply - 5 V
- a printed circuit board, programmed layout and documentation in the set
A version with a set of components for self-assembly is available- Detailed description in EP 4/04
Download
193811
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
This breakout board for TI’s DRV8880 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/16-step).
Retired
No product available!
Wheels fit 2 mm diameter output shafts such as the ones on our sub-micro plastic planetary gearmotors. Pololu - 2356
Retired
No product available!
JEKEN CE-6200A ultrasonic cleaner, with digitally adjustable working time, power 70 W and a capacity of 1.4 l. It is well suited for repair and maintenance of electronic components, PCBs, optical elements, as well as for the dissolution of polymers
Retired
No product available!
Rick Waldron, Anna Gerber, David Resseguie, Emily Rose, Susan Hinton, Sara Gorecki, Bryan Hughes, Andrew Fisher, Julian David Duque, Pawel Szymczykowski, Donovan Buck, Jonathan Beri, Kassandra Perch, Raquel Vélez, Lyza Danger Gardner
Retired
No product available!
The grapple is used for precise operations when replacing SMD and BGA circuits. It allows you to lift small electronic components without using tweezers
Retired
No product available!
Spray CLEANSER PCC 15 with a capacity of 150ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
Spray CLEANSER PCC 15 with a capacity of 400ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
No product available!
Dispensing needle for precise application of glue, flux with an inner diameter of 0.62mm and an external diameter of 0.9mm.
Retired
No product available!
Dosing needle for precise application of glue, flux with an inner diameter of 0.25 mm and an external diameter of 0.51 mm
Retired
No product available!
No product available!
Dosing needle for precise application of glue, flux with an inner diameter of 0.51mm and an external diameter of 0.82mm
Retired
No product available!
Dosing needle for precise application of glue, flux with an inner diameter of 0.9mm and an external diameter of 1.2mm
Retired
No product available!
PROGRAMMED REMOTE CONTROLLER - PLATEBOARD AND PROGRAMMED LAYOUT