- Out-of-Stock
47:1 Metal Gearmotor 25Dx52L mm HP with 48 CPR Encoder
This cylindrical, 2.54" x 0.98" x 0.98" gearmotor uses a brushed DC motor with extra-strong magnets and a 46.851:1 metal gearbox to deliver a lot of power in a relatively small package. It has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 2249 counts per revolution of the gearbox’s output shaft. These units have a 0.315"-long, 4 mm-diameter D-shaped output shaft. We also carry a lower-power version of this gearmotor and a version without an encoder.
Key specs at 6 V: 210 RPM and 450 mA free-run, 80 oz-in (5.8 kg-cm) and 6 A stall.
This brushed DC gearmotor is available in high- and low-power versions in a number of gear ratios. Many other gear ratios are also available without an encoder.
| Gear Ratio | Speed @ 6V | Stall Torque @ 6V | Stall Current @ 6V | ![]() With Encoder | ![]() Without Encoder |
|---|---|---|---|---|---|
| 4.4:1 | 2020 RPM | 8 oz-in | 6 A | 25Dx48L mm HP | |
| 1280 RPM | 5 oz-in | 2.2 A | 25Dx48L mm | ||
| 9.7:1 | 1010 RPM | 17 oz-in | 6 A | 25Dx48L mm HP | 25Dx48L mm HP |
| 580 RPM | 11 oz-in | 2.2 A | 25Dx48L mm | 25Dx48L mm | |
| 20.4:1 | 480 RPM | 36 oz-in | 6 A | 25Dx50L mm HP | |
| 275 RPM | 24 oz-in | 2.2 A | 25Dx50L mm | ||
| 34:1 | 285 RPM | 60 oz-in | 6 A | 25Dx52L mm HP | 25Dx52L mm HP |
| 165 RPM | 40 oz-in | 2.2 A | 25Dx52L mm | 25Dx52L mm | |
| 47:1 | 210 RPM | 80 oz-in | 6 A | 25Dx52L mm HP | 25Dx52L mm HP |
| 120 RPM | 50 oz-in | 2.2 A | 25Dx52L mm | 25Dx52L mm | |
| 75:1 | 130 RPM | 130 oz-in | 6 A | 25Dx54L mm HP | 25Dx54L mm HP |
| 75 RPM | 85 oz-in | 2.2 A | 25Dx54L mm | 25Dx54L mm | |
| 99:1 | 100 RPM | 160 oz-in | 6 A | 25Dx54L mm HP | |
| 57 RPM | 110 oz-in | 2.2 A | 25Dx54L mm | ||
| 172:1 | 57 RPM | 260 oz-in | 6 A | 25Dx56L mm HP | |
| 33 RPM | 170 oz-in | 2.2 A | 25Dx56L mm | 25Dx56L mm | |
| 227:1 | 25 RPM | 220 oz-in | 2.2 A | 25Dx56L mm | |
| 378:1 | 15 RPM | 250 oz-in | 2.2 A | 25Dx58L mm | |
| 499:1 | 12 RPM | 300 oz-in | 2.2 A | 25Dx58L mm |
Note: At some of the higher gear ratios, these motors can generate enough torque to damage themselves. Any torque greater than about 250 oz-in (18 kg-cm) is likely to damage the gearbox, so we recommend that you avoid stalling the 172:1 HP, 227:1, 378:1, and 499:1 versions of these motors at 6 V.
These motors are intended for use at 6 V. In general, these kinds of motors can run at voltages above and below this nominal voltage, so they should comfortably operate in the 3 – 9 V range, though they can begin rotating at voltages as low as 1 V. Higher voltages could start negatively affecting the life of the motor.
These gearmotors have output shafts with a diameter of 4 mm. The Pololu universal aluminum mounting hub for 4mm shafts can be used to mount our larger Pololu wheels (60mm-, 70mm-, 80mm-, and 90mm-diameter) or custom wheels and mechanisms to the gearmotor’s output shaft (see the left picture below). These are the same type of motors used in the Wild Thumper all-terrain chassis, and the gearbox’s output shaft works directly with the 120mm-diameter Wild Thumper wheels.
![]() |
| 25D mm metal gear motor with 48 CPR encoder and Pololu 60×8mm wheel. |
|---|
The face plate has two mounting holes threaded for M3 screws. You can use our custom-designed 25D mm metal gearmotor bracket (shown in the picture below) to mount the gearmotor to your project via these mounting holes and the screws that come with the bracket.
![]() |
| Pololu 25D mm gearmotor with bracket. |
|---|
The diagram below shows the dimensions (in mm) of the 25D mm line of gearmotors. The value of L is shown in the table below.
|
|
![]() |
| 25D mm metal gearmotor with 48 CPR encoder. |
|---|
A two-channel Hall effect encoder is used to sense the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 48 counts per revolution of the motor shaft. To compute the counts per revolution of the gearbox output, multiply the gear ratio by 48. The motor/encoder has six color-coded, 11" (28 cm) leads:
| Color | Function |
|---|---|
| Black | motor power |
| Red | motor power |
| Blue | Hall sensor Vcc (3.5 – 20 V) |
| Green | Hall sensor GND |
| Yellow | Hall sensor A output |
| White | Hall sensor B output |
These leads have stripped, unterminated ends that can be soldered or crimped to make solder free connectors. The Hall sensor requires an input voltage, Vcc, between 3.5 and 20 V and draws a maximum of 10 mA. The A and B outputs are square waves from 0 V to Vcc approximately 90° out of phase. The frequency of the transitions tells you the speed of the motor, and the order of the transitions tells you the direction. The following oscilloscope capture shows the A and B (yellow and white) encoder outputs using a motor voltage of 6 V and a Hall sensor Vcc of 5 V:
![]() |
| Encoder A and B outputs for 25D mm HP metal gearmotor with 48 CPR encoder (motor running at 6 V). |
|---|
By counting both the rising and falling edges of both the A and B outputs, it is possible to get 48 counts per revolution of the motor shaft. Using just a single edge of one channel results in 12 counts per revolution of the motor shaft, so the frequency of the A output in the above oscilloscope capture is 12 times the motor rotation frequency.
May 5, 2012 Update: We are transitioning to encoders with leads terminated by a 1×6 0.1” female header. If you receive an encoder with such a header, you can pull the crimped wires out of the header or cut the header off if you just want the individual wires.
We offer a wide selection of metal gearmotors that offer different combinations of speed and torque. Our metal gearmotor comparison table can help you find the motor that best meets your project’s requirements.
![]() |
| Some of the Pololu metal gearmotors. |
|---|
Data sheet
Manufacturer
Responsible person
Android TV BOX multimedia player with SMART TV function. Designed for TVs with an HDMI connection and the ability to play in 4K UltraHD quality. Blow Android TV BOX
No product available!
Camera with a resolution of 5 MPx with a USB interface in a metal case. Equipped with an OV5648 CMOS sensor with a wide angle lens with a 90° angle of view. ArduCAM UB023301
No product available!
Camera with a resolution of 8 MPx with a USB interface. Equipped with a CMOS IMS179 sensor with a wide-angle lens with a viewing angle of 150°. ArduCAM UB0233
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Juicy Green
No product available!
ROSA3D filament made of high-quality PET-G granules. 0.5 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G Standard Glow in the Dark Green
No product available!
HMI module with a color LCD TFT 4.3" display with a resolution of 480x272 pixels. Equipped with a capacitive touch panel. Communication via UART interface. Accessories included. DWIN DMG48270C043_05WTC-SET
No product available!
The MP2307 converter module is an ideal solution for efficient and stable power supply of devices, offering a wide range of adjustable output voltages and continuous current up to 3 A. Thanks to the soft start function, it ensures long-lasting and reliable operation, protecting the system against sudden voltage spikes when switching on
No product available!
Adapter with a set of connectors specific to the Raspberry Pi 3 Model B/B+. It allows you to adapt the Raspberry Pi CM4 modules to projects based on Pi 3 model B/B+. Waveshare CM4-to-Pi3-Adapter
No product available!
Convenient to use retractable 3in1 USB cable with USB A plug and three output connectors: microUSB, USB Type C and Lightning
No product available!
Convenient to use retractable 3in1 USB cable with USB A plug and three output connectors: microUSB, USB Type C and Lightning
No product available!
Adapter with RPi CM4 socket and CM3 SODIMM connector. It allows you to connect the Raspberry Pi Compute Module 4 minicomputer to the base boards dedicated to CM3 modules. Waveshare Zero-to-CM3-Adapter
No product available!
Module with nRF52840 microcontroller with ARM Cortex M4F core and Bluetooth 5.0 communication. Waveshare Core52840
No product available!
Wall charger with built-in USB type-C cable. The maximum current generated by the charger is 3.1 A. eXtreme NTC31C
No product available!
Precision 25 turn potentiometer used to adjust resistance in circuits, ideal for applications requiring accurate settings and THT assembly
No product available!
The TL431AILP is a precision, adjustable shunt voltage reference regulator, ideal for use in switching power supplies, voltage regulation circuits, and as a replacement for Zener diodes in applications requiring a stable reference voltage. Thanks to its wide output voltage range and high accuracy, this component is used in various electronic projects, providing reliability and precise performance.
No product available!
The Molex 53261-0571 is a 1.25 mm pitch 5-pin header designed for PCB mounting in compact applications. With its 90° angled design and robust construction, it provides a reliable signal connection in electronic systems such as telecommunications and industrial electronics.
No product available!
47:1 Metal Gearmotor 25Dx52L mm HP with 48 CPR Encoder