- Out-of-Stock

FPV 433Mhz Radio Telemetry Kit 100mW V1.1 (42847)
This Telemetry radio set allows you to link to a flight controller such as our HK Pilot Mega 2.5 or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). The Radio set not only lets you see live data such as live GPS position overlaid on a map (if the flight controller has the GPS option) to system voltage, heading, waypoint navagation even artificial horizon and so much more, using open source MAVlink based ground station software. You can even fly your aircraft with a joystick via your computer and update settings live! Or just use it for your DIY projects that needs a wireless Serial interface. This kit offers a great low price, longer range (approx one mile with supplied antennas) and superior performance. The system utilizes the 433Mhz band and provides a full-duplex link using HopeRFs HM-TRP modules running custom, open source, firmware.
The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and configuration of system parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.
Interface to the module is via standard 5V-tolerant TTL serial / FT232 USB serial.
Features:
• Very small size
• Light weight (under 4 grams without antenna)
• 433Mhz frequency band
• Receiver sensitivity to -117 dBm
• Transmit power up to 20dBm (100mW)
• Transparent serial link
• Air data rates up to 250kbps
• Range of approx 1 mile with supplied antennas
• Demonstrated range of several kilometers with a small omni antenna
• Can be used with a bi-directional amplifier for even more range
• MAVLink protocol framing and status reporting
• Frequency hopping spread spectrum (FHSS)
• Adaptive time division multiplexing (TDM)
• Support for LBT and AFA
• Configurable duty cycle
• Built in error correcting code (can correct up to 25% data bit errors)
• Open source firmware
• AT commands for radio configuration
• RT commands for remote radio configuration
• Adaptive flow control when used with APM
• Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller.
• Upgraded to more convince Molex 1.25mm
Specs:
Band: 433MHz
Antenna connectors: RP-SMA connector
Output power: 100mW (20dBm), adjustable between 1-20dBm
Sensitivity: -117dBm sensitivity
Interface: Standard TTL UART
Connection status: LED indicators
Includes:
Radio Telemetry base station (USB Connection)
Telemetry Transceiver (Pin Header)
lead set x1
Antenna x 2
This product is based on the 3DRadio Project from 3D Robotics.
PRODUCT ID: 9387000030-0
Download
Customer files | ||
No File Name | 317kb | |
setup tool | 317kb | |
Ftdi Driver | 3238kb | |
Osd and 433Mhz | 2681kb | |
Telemetry and Osd | 2681kb | |
Telemetry mount on cabin | 3524kb | |
No File Name | 4190kb | |
Telemetry mount on cabin | 4190kb | |
Telemetry mount on cabin | 2802kb | |
Original Antenna Spectrum Test | 5256kb | |
Wiring to arduino (using sensor shield) | 3106kb | |
Telemetry range upgrade | 268kb |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
A simple unipolar stepper motor driver assembled. AVT1814 C
No product available!
No product available!
No product available!
PCB and pre-programmed system for LED controller controlled by any remote control. AVT3133 A +
No product available!
Assembled 6V gel battery protection. AVT1970 C
No product available!
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 150 MHz and the ability to measure voltage up to 1500 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP1501
No product available!
No product available!
No product available!
The board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM. The board also has 16 MB of QSPI flash memory. The system can be programmed in C/C++ or microPython. SparkFun DEV-17717
No product available!
Needle bending needle, for precise glue application, Flux 0.81mm internal diameter and 1.26mm outside diameter
No product available!
8-bit ST7 MCU, 8kB Flash, 384B RAM, Lite Timer with Watchdog, Autoreload Timer with 32-MHz input clock, SPI, 10-bit ADC with Op-Amp, DIP20, RoHS
No product available!
No product available!
Ultrasonic cleaner with a capacity of 0.75l and 50W for cleaning CDs, jewelery as well as various spare parts and electronic components. JEKEN CE-5600A
No product available!
No product available!
No product available!
ARK terminal connector with a fuse, 2-pin, pitch 10.00 mm, non-detachable.
No product available!
HK FPV 433Mhz Radio Telemetry Kit 100mW V1.1 (42847)