- Out-of-Stock

HDMI 4 Pi: 5" Display no Touchscreen 800x480 - HDMI/VGA/NTSC/PAL
Description
Yes, this is a cute little 5" TFT display with WVGA 800x480 resolution. We tried to get the smallest display that would be good for embedded computing usage and at a good price. The visible display measures 5" diagonal and is a raw TTL display as is used in portable electronics. We include a driver board with HDMI, VGA and Composite inputs. The display is very easy to use - simply connect a 5-12V DC adapter to the 2.1mm center-positive DC jack, then connect a digital video source to one of the ports. Voila, a display!
It is not an IPS display so its best for direct viewing, our 7" and 10" HDMI IPS displays are designed for any angle view.
Theres a little wired PCB with little buttons that let you enter a menu system for adjusting brightness, color and contrast. It tries to auto-detect which input you have and switches to that one or you can select from the menu keypad which to display.
To demonstrate it, we took some photos with the display connected to a Raspberry Pi, but it will also work connected to any device with HDMI, VGA or NTSC/PAL output. It will not work with a device that only outputs DVI (without a DVI->HDMI converter) or SECAM.
For use with a Raspberry Pi we suggest editing config.txt to set the HDMI to 800x480 in case it doesnt detect the resolution properly. You can see our suggested config.txt in the Technical details tab. The easiest way to edit the config.txt is to put the Pi SD card into an every day computer and edit config.txt with any text editor and save. For use with a BeagleBone black, we found it works when plugged in, no configuration required.
We show the TFT above on a wire stand, which is not included. You can pick up one of these nice stands over here. If you want to extend the FPC cable between the driver and the TFT, you can grab a 10" long cable and swap it for the 4" one included.
A power adapter is not included! Any 5 to 12VDC adapter will work nicely: we prefer 9V DC. Check the technical tabs for current draw at various voltages.
Specifications
Download
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
The fan designed for use with the Digilent ZYBO Z7-20 plate mounted on the heat sink allows better air flow, which results in lowering the FPGA temperature. The fan has a 3-pin connector, the supply voltage is 5 V. In addition to the fan, there are screws for fixing. Digilent 240-130
No product available!
No product available!
No product available!
No product available!
The DDS generator with alphanumeric display allows you to generate sine, rectangular or triangle waveforms with a frequency of up to 5MHz. The device can also be used to measure frequencies in the 1Hz-60MHz range.
No product available!
No product available!
Folded bending needle, for precise glue application, flux with 0.51mm internal diameter and 0.8mm outside diameter
No product available!
No product available!
No product available!
No product available!
No product available!
6-port IO port expander for M5Stack kits. It is equipped with 6 Grove connectors, it is based on the ATmega328 microcontroller, which communicates via the I2C interface. M5Stack PbHUB Unit
No product available!
No product available!
No product available!
No product available!
Adafruit 1678 - little 5" TFT display with WVGA 800x480 resolution