- Out-of-Stock
C Tinkering Kit for Odroid C1/C1+/C0/C2
ID: 559055
What you need is an add on prototyping T-breakout board, which can break out all those tasty power, GPIO, I2C, ADC pins from the 40 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the ODROID-C1 super easy
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Overview
Youre probably itching to make some fun embedded computer projects with ODROID-C1. What you need is an add on prototyping T-breakout board, which can break out all those tasty power, GPIO, I2C, ADC pins from the 40 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the ODROID-C1 super easy.
This kit comes with below many items.
- Assembled T-breakout PCB - 40Pin GPIO Breakout board
- Breadboard - 630 Tie-points with dual power lanes
- 40pin Ribbon cable - IDC Flat cable 100mm
- 40pin Male-to-Male Dupont jumper Wire 170mm
- 7 x Green LED 3mm
- 7 x Yellow LED 3mm
- 7 x Red LED 3mm
- 2 x Photo Cell (CdS Light sensor)
- 6 x Tact Swithc
- 50 x 330 Ohm 1/6W resister
- 50 x 10K Ohm 1/6W resister
R-type Breakout
With this T-type breakout board you can easily break out the GPIO pins of the ODROID-C1/C2/C0/C1+ on a breadboard to quickly start prototyping. The ribbon cable comes at the side of the breadboard so it wont be in the way while working on your project.
This breakout also has the possibility to provide +5V and +3.3V to the power rails on a 630 points breadboard.
Simple project with the C1 Tinkering Kit
19 LEDs + CdS light sensor will show you how ADC and LED work.
Notes:
The CdS is connected to the ADC #0 port with a 10Kohm ground bias. 3.3V - CdS - Cds - ADC - GND The LED is connected to the GPIO via 330ohm in serial. GPIO - LED(A+) - LED(K-) - 330ohm - GND 
Connect it to your ODROID-C1 with the Flat cable.
Download
559055
Other products in the same category (16)
No product available!
3D stereo camera module, which was built of two cameras with OV9281 sensor. Designed to work with Raspberry Pi, Jetson Nano and Xavier NX. ArduCAM B0263
Retired
No product available!
Motor with 48 CPR Encoder for 25D mm Metal Gearmotors (No Gearbox)
Retired
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Rainbow Silk
Retired
No product available!
No product available!
Permanent cylindrical neodymium magnet with a diameter of 4 mm and a height of 3 mm.
Retired
No product available!
JTAG/SWD emulator with Trace for Cortex-M devices, RoHS, Segger
Delivery date unknown
No product available!
No product available!
NetFPGA-SUME Virtex-7 FPGA Development Board. The amazingly advanced board that features one of the largest and most complex FPGA’s ever produced, a Xilinx Virtex-7 690T supporting thirty 13.1 GHz GTH transceivers. 410-301
Retired
No product available!
No product available!
Gamepad extension with buttons and a joystick that enable the micro: bit to create a game console. The module additionally has a buzzer and a Li-ion battery port charged via the USB port.
Retired
No product available!
Printed circuit board of the '51 family of microcontrollers programmer with Flash memory and EPROM in housings with 20 or 40 pins
Delivery date unknown
No product available!
ICP programmer for ST7F Flash microcontrollers
Delivery date unknown
No product available!
Low-power (LP), 12V 25D mm metal gearmotors with 48 CPR encoders. It does not include a gearbox, but the pinion gear on the output shaft works with all of our 25D mm gearmotor gearboxes, so this can be used as a replacement motor or encoder for those gearboxes. Pololu 3260
Retired
No product available!
Flex Cable for Raspberry Pi Camera - 100mm / 4". Adafruit 1646
Retired
No product available!
Assembled automatic power switch for car installation. AVT1877 C
Retired
No product available!
What you need is an add on prototyping T-breakout board, which can break out all those tasty power, GPIO, I2C, ADC pins from the 40 pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the ODROID-C1 super easy