- Out-of-Stock
Wireless 4-channel remote for Arduino
ID: 564687
Remote control for Arduino; 315MHz; 4 buttons
Description
Remote control for Arduino; 315 MHz; 4 buttons.
properties
- Power supply: 5 V
- Remote control: 27A type battery
- Power consumption: 10 mA
- Outbox Mac: 10 mW
- Number of buttons: 4
- Operating frequency: 315 MHz
- Modulation: ASK
- Receiver sensitivity: -98 dBm
- Range: 50 ... 100 m
The receiver contains 7 pins: VT, D0, D1, D2, D3, 5V and GND. At the moment of pressing the button on the remote control, the appropriate pin goes into high state (for button A - D2, B - D0, C - D3, D - D1). The VT pin goes into high state when any signal from the transmitter is received. For 5 V and GND pins, the power supply and system ground must be connected accordingly.
Both the remote control and the receiver can be set to an 8-bit address. The address of the receiver and the transmitter should be the same so that they can communicate. Address settings are made by shortening the free pins of the system to the upper (power) bus, or to the lower (mass) busbar.
Included
- Wireless remote control with sliding antenna and battery
- Receiver module
Attention!
Due to the regulations in force in Poland, ISM 315 MHz radio channels can only be used for testing purposes
564687
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
Sound card (USB adapter) with small dimensions with two sockets for connecting a microphone and headphones. UGO UKD-1086
Retired
No product available!
Starter kit with micro:bit v2. Includes USB cable, battery basket and PVC casing. OKdo micro:bit Getting Started Kit
Retired
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Retired
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Retired
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Retired
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Retired
No product available!
A portable Smart oscilloscope with an 8-inch LCD display and a touch screen. It has two measurement channels and has good measurement parameters: 200 MHz band, 2 GSa/s sampling rate and 280 Mpts memory buffer. Micsig STO2202C
Retired
No product available!
A portable Smart oscilloscope with an 8-inch LCD display and a touch screen. It has two measurement channels and has good measurement parameters: 150 MHz band, 1 GSa/s sampling rate and 70 Mpts memory buffer. Micsig STO1152E
Retired
No product available!
Industrial RS485 - Ethernet converter. It is equipped with PoE function and is DIN-rail mounted. Waveshare RS485 TO POE ETH (LF)
Retired
No product available!
10.3" monitor with e-Paper screen equipped with a mini HDMI interface. It offers a resolution of 1872×1404 pixels, a wide viewing angle and low power consumption. Waveshare EINK-DISP-103B (EU)
Retired
No product available!
9.7" monitor with e-Paper screen equipped with a mini HDMI interface. It offers a resolution of 1200x825 pixels, a wide viewing angle and low power consumption. Waveshare EINK-DISP-97 (EU)
Retired
No product available!
A portable gaming console based on the Raspberry Pi Zero, featuring a 2" IPS LCD display and speaker. Waveshare GamePi20 Acce
Retired
No product available!
High voltage differential probe. It is characterized by good measurement parameters: 100 MHz band and working voltage up to 750 V. The probe has two attenuation factors: 50X and 500X and uses the UPI interface. Micsig DP750-100
Retired
No product available!
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 5600 V. The probe has two attenuation factors: 200X and 2000X. Micsig DP20003
Retired
No product available!
Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 100 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP1003
Retired
No product available!
Probe for measuring direct and alternating current with a current of up to 30 A. Works in the band up to 50 MHz, it can be connected to the oscilloscope through the UPI connector. It does not require an external power supply. Micsig CP503
Retired
No product available!
Remote control for Arduino; 315MHz; 4 buttons