Basys MX3: PIC32MX Trainer Board for Embedded Systems Courses

Description

The Basys MX3 is a development platform for the Microchip PIC microcontroller (PIC32MX370). With an exhaustive set of peripherals, users can create a wide range of embedded systems applications. The board also provides an easy and cost-effective introduction to the PIC32 microcontroller and  MPLAB® X Integrated Development Environment (IDE). A complete set of software libraries are included, allowing users to make simple function calls to all onboard peripherals, greatly simplifying the development process. With the on-board debug headers and USB programmer/debugger, users can debug their designs directly from MPLAB® X Integrated Development Environment, or scope digital and analog signals through Analog Discovery 2 or Digital Discovery.

Accompanied by free and open-source coursework, including 7 in-depth teaching units and 15 complete labs, the Basys MX3 is also a versatile MCU trainer board ideal for teaching introductory embedded systems courses. It covers topics from toggling LED’s motor control to digital signal processing. The coursework is designed for sophomore/junior level embedded systems courses.

Features

• Processor/IC: Microchip PIC32MX370F512L Microcontroller
• MIPS32® M4K® core runs up to 96 MHz using onboard 8 MHz oscillator
• 512 KB of Program Flash Memory
• 12KB of Boot Flash Memory
• 128 KB of SRAM
• Four Direct Memory Access (DMA) Modules
• Two SPI, Two I²C, and Five UART serial interfaces
• Parallel Master Port (PMP) for graphics interfaces
• Five 16-bit Timers/Counters
• Five Input Capture Modules
• Five Output Compare Modules
• 85 I/O pins
  • 54 pins support Peripheral Pin Select (PPS) for function remapping

• Software
  • Designed for use with MPLAB X IDE
• System Features
  • 4 MB SPI Flash
  • Onboard USB UART (USB Micro cable required, NOT INCLUDED)
    • Supports baud rates up to 1.25 MBaud
  • Powered from USB or 5 V external power source
    • Standard barrel jack for 2.0 mm internal-diameter plug
    • No jumper select required

• System Connectivity
  • USB-UART Bridge
• Interaction and Sensory Devices
  • 8 Slide Switches
  • 5 Buttons
  • 1 Reset Button
  • 8 LEDs
  • 1 RGB LED
  • Onboard 3-axis, 12-bit accelerometer
    • Programmable Motion Detection
    • I2C Interface with Programmable Interrupt
  • Onboard FIR-compatible IrDA Module
    • Built-in Remote Control Transmission Function
    • Supports speeds up to 4 Mbps
  • Onboard Audio Input and Output
    • MEMS Microphone with Adjustable Gain
      • Thumbwheel potentiometer for adjusting mic volume
    • PWM driven mono audio output with onboard speaker
      • Thumbwheel potentiometer for adjusting speaker volume
      • 3.5 mm jack for line out connection to external amplifier/speaker system
  • Onboard Displays
    • 2x16 LCD Character Display with LED backlight
    • 4-Digit Seven Segment Display with red LEDs

• Motor Control
  • Onboard Dual H-Bridge Motor Driver
    • Supports up to two 1.5 A Brushed DC Motors or one stepper motor
    • Supports motor voltages up to 11 V
    • Terminal block provides easy connection to motors
  • 2 Servo Connectors
• Analog Input Control (AIC)
  • Thumbwheel potentiometer for varying analog input between 0 to 3.3 V
  • Two wire loops for ground and AIC
• Expansion Connectors
  • Two 2×6 Pmod host ports
    • SPI, UART, GPIO, PWM, analog in
  • Terminal block for two DC motors or one stepper motor
  • Two R/C servo connectors
  • One I²C connector
• Debugging
  • On-board 30-pin Analog Discovery 2 connector
  • On-board USB programmer/debugger
    • Program/debug the PIC32MX370 directly from MPLAB / MPLABX
• Support
  • 7 free and open-source teaching units complete with 15 labs
  • Enough content to support one to two semesters of undergraduate embedded systems coursework