- Out-of-Stock
Filament ROSA3D PLA Starter 1.75mm Natural Transparent
ID: 587819
5907753130105
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Natural Transparent
Description
1.75 mm PLA filament for 3D printing by ROSA3D. 0.8 kg of filament is wound on the spool. The recommended printing temperature is in the range from 185°C to 225°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
PLA is the basic material used in 3D printing. PLA Starter is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable biopolymer. It was made of ingredients approved for contact with food.
Features
- Color: Natural Transparent
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02 mm
- Printing temperature: 185°C to 225°C
- Bed temperature: 40°C to 60°C (when using washers or other means to increase the adhesion heating of the table is not required)
- Density 1.24 g/cm3
- Odorless smell
- Elongation at tensile 6%
- Tensile strength (to break) 53 MPa
- Modulus of elasticity at tensile 3500 MPa
- Heat deformation temperature 55°C
- Net weight: 0.8 kg
587819
Data sheet
- Rodzaj filamentu
- PLA
- Ilość filamentu
- 0,8 kg
- Diameter
- 1,75 mm
- Colour
- White
You might also like
3D printer with dual color print and heated table. The printer is fully assembled and ready to use. Flashforge Creator PRO
Regular pricezł4,365.91zł3,199.00
24h
Available quantity: 1
Available
Easy PLA filament in black, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Black
zł75.03
24h
Available quantity: 3
Available
Easy PLA filament in gray, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Gray
zł75.01
24h
Available quantity: 2
Available
Other products in the same category (16)
Integrated analogue base station RFID (front-end) of the company EM Microelectronic with a frequency of 13.56MHz. The system has a SOP20 housing
Retired
No product available!
Computer fan housing Raspberry Pi 3, Raspberry Pi 2 model B and Raspberry Pi 1 model B + in dark blue plastic color
Retired
No product available!
Case for the Raspberry PI 2 model B, Raspberry PI 1 model B+ and Raspberry PI 3 computers, manufactured from high quality acrylic. CLEAR
Retired
No product available!
No product available!
No product available!
No product available!
Infrared sensor that allows measurement of distances up to 15cm, has a built-in infrared illuminator, IR receiver and a perimeter of the received signal
Retired
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. Antenna: copper wire
Retired
No product available!
Ultra miniature WiFi b/g/n module, equipped with UART, SPI, PWM and GPIO interfaces. The ability to work as an access point and in standalone mode. 3.3V power supply.HF-LPT200-1
Retired
No product available!
This transducer is about 45mm in diameter and has 4Ω impedance and should be run at about 5W
Retired
No product available!
SPIRIT1 868 MHz low power RF module with integrated microcontroller
Delivery date unknown
No product available!
Read/Write analog front end for 125 kHz RFID Basestation, SOIC16, EM Microrlectronic, RoHS
Retired
No product available!
Bitscope Micro is a miniature measuring instrument with a USB interface, it can act as an 8-channel logic analyzer (40MS / s, 3.3V or 5V) or a 2-channel oscilloscope (bandwidth up to 20MHz). In addition, Bitscope can generate a clock signal as well as sinusoidal, triangular, rectangular and saws
Retired
No product available!
High performance WLAN USB module which enables the Raspberry Pi to connect to a Wi-Fi network
Retired
No product available!
Kit for building a minisumo robot on a crawler chassis. It has a bulldozer, control board and a set of caterpillars. Robot version for self-assembly, requires additional motors and four AA batteries. Pololu 3124
Retired
No product available!
Expansion module kit with Arduino compatible connectors for building a Zumo robot. The module includes a dual engine controller, buzzer and user button, as well as a 3-axis accelerometer and compass. Pololu 2508
Retired
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Natural Transparent