- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
DV164005
ID: 59203
Microchip MPLAB ICD 2
Microchip MPLAB ICD 2 Module
The MPLAB ICD 2 module is a low-cost development tool that connects between the PC and the designer’s target board, allowing direct in-circuit debugging of a target PICmicro MCU or dsPIC DSC. Programs can be executed in real time or single step, watch variables established, break points set, memory read/writes accomplished and more. It can also be used as a development programmer. This kit contains the MPLAB ICD 2 module, an ICD interface cable and USB cable.
The MPLAB ICD 2 module is a low-cost development tool that connects between the PC and the designer’s target board, allowing direct in-circuit debugging of a target PICmicro MCU or dsPIC DSC. Programs can be executed in real time or single step, watch variables established, break points set, memory read/writes accomplished and more. It can also be used as a development programmer. This kit contains the MPLAB ICD 2 module, an ICD interface cable and USB cable.
Key Features:
- Real time background debugging
- MPLAB IDE GUI
- Built in over-voltage/short circuit monitor
- Firmware upgradeable from PC
- Totally enclosed
- Supports low voltage to 2.0 volts. (2.0 to 6.0 range)
- Diagnostic LEDs (Power, Busy, Error)
- Reading/Writing memory space and EEDATA areas of target microcontroller
- Programs configuration bits
- Erase of program memory space with verification
- Peripheral freeze-on-halt stops timers at breakpoints
Package Contents:
- MPLAB ICD 2 Module
- ICD interface cable
- USB cable
59203
Other products in the same category (16)
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
Stephen Chin, Dean Iverson, Oswald Campesato, Paul Trani
Delivery date unknown
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
Retired
No product available!
Sub-micro analog servo with plastic gear. It has a range of motion of 180°. Pololu 1040
Retired
No product available!
No product available!
No product available!
No product available!
Open-source single-board computer (SBC), can run Android 4.2, Android 4.4*, Ubuntu, Debian, Fedora, Raspbian, ArchLinux, openSUSE, OpenWrt, Bananian, and other Linux OS systems such as Gentoo and Fedora. It uses the AllWinner A20 SoC, and has 1GB DDR3 SDRAM with wired Gigabit ethernet (RJ45 socket) and a SATA port
Delivery date unknown
No product available!
Orange Pi 3 1GB is a mini-computer equipped with SoC Allwinner H6 (quad-core, frequency up to 1.8 GHz, 64-bit architecture, ARM Cortex ™ -A53 core). It has 1GB RAM (LPDDR3), Mali T720 graphics chip, 8GB eMMC memory. The board can run Android 7.0 and Linux.
Retired
No product available!
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32
Retired
No product available!
Minicomputer equipped with SoC Rockchip RK3399 (ARM Cortex-A72 / ARM Cortex-A53). It has a 4 GB DDR3 RAM memory. The computer has been well-equipped, including Gigabit Ethernet connector, mSATA interface, miniPCIe connector, USB type C, dual CSI interface, etc.
Retired
No product available!
SD Card Kingston CANVAS React 32GB Class 10. SDR / 32GB
Retired
No product available!
No product available!
No product available!
PLATEBOARD - PROGRAMMED CONTROLLER FOR TOYS AND MODELS - CONTROLLER PRINTED BOARD
Retired
No product available!
Microchip MPLAB ICD 2