STEMMA QT AD5693R Breakout - module with 16-bit DAC converter
ID: 1188205
zł64.21
Tax included
zł52.20 tax excl.
Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
DAC converter module based on the AD5693R chip, which offers amazing 16-bit resolution. This means you can precisely control the output voltage, which is ideal for advanced applications. The DAC converter works with both 3.3V and 5V. Moreover, you have full control over the maximum output voltage. You can set them to 2.5V or 5V (2 times Vref). This gives you the flexibility to adapt the module to the requirements of your project. If you power it with 3.3V, the output range is 0 to 3.3V.
The converter supports a fast I2C bus with a speed of 3.4 Mbps, which allows the output voltage to be updated with a frequency of approximately 200 kHz. Thanks to the EEPROM memory, you can save the set output voltage and even after turning off the power, the module restores the stored voltage. Additionally, the module has an ADDR pin that allows you to configure the I2C address. This allows you to connect two DAC converter modules to one bus. All this makes the DAC converter module an excellent tool for advanced applications that require accurate voltage control.
Features
- AD5693R chip
- High relative accuracy (INL): maximum ±2 LSB at 16 bits
- Low drift, 2.5V reference voltage: 2 ppm/°C typical
- Selectable output range: 2.5 V or 5 V
- Total Uncorrected Error (TUE): ±0.06% of the maximum FSR value
- Offset error: ±1.5 mV maximum
- Gain error: ±0.05% of maximum FSR
- Low error: 0.1 nV-sec
- Current capacity: 20 mA
- I2C interface
- STEMMA QT connector
- Wide operating temperature range: from -40°C to +105°C
- Dimensions: 25.2 x 17.6 x 4.8 mm
Kit contains
- STEMMA QT AD5693R Breakout module
- Goldpin male straight 8-pin connector
1188205
You might also like
4-wire cable with a length of 50 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4399
zł5.71
24h
Available quantity: 20
Available
4-wire cable with a length of 100 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4210
zł6.62
24h
Available quantity: 26
Available
4-core cable with a length of 200 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 4401
zł8.68
24h
Available quantity: 8
Available
4-core cable with a length of 300 mm. Both ends with STEMMA QT (Qwiic) plug. Adafruit 5384
zł7.27
24h
Available quantity: 13
Available
Other products in the same category (16)
The module with the I2C controller based on the HT16K33 system. Dedicated to 14-segment displays. It is equipped with STEMMA QT connectors. Adafruit 1910
zł33.87
24h
Available quantity: 3
Available
The module with the buffer of the I2C bus based on the TCA4307 system. It allows you to connect I2C devices with active power supply. Equipped with a STEMMA QT connector. Adafruit 5159
zł30.64
24h
Available quantity: 2
Available
Module with a light intensity sensor LTR-329. It offers a measuring range from 1 to 65535 lux and a 16-bit resolution. Communication takes place using I2C. Adafruit 5591
zł36.29
24h
Available quantity: 4
Available
Module with a temperature and humidity sensor based on the HTU31 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4832
zł39.52
24h
Available quantity: 4
Available
A digital temperature and humidity sensor module based on the SHT41 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5776
zł35.45
24h
Available quantity: 2
Available
Module with CO2, temperature and humidity sensor SCD-41. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5190
zł486.45
24h
Available quantity: 1
Available
Module with 8-bit ADC and 8-bit DAC. It allows you to measure voltage and generate an analog signal. Communicates via I2C. Adafruit 4648
zł39.99
24h
Available quantity: 1
Available
Module with a logarithmic digital potentiometer based on the DS1841 chip. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4570
zł33.85
24h
Available quantity: 5
Available
Module with acceleration and rotational speed sensor based on the LSM6DSO32 chip. Equipped with a STEMMA QT connector, it communicates via the I2C or SPI interface. Adafruit 4692
zł68.62
24h
Available quantity: 3
Available
Module with EEPROM 24LC32 memory with a capacity of 32 kBit (4 kB). Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5146
zł22.30
24h
Available quantity: 4
Available
Module with a digital barometer DPS310. It enables pressure measurement in the range from 300 to 1200 hPa and communicates via I2C or SPI. Adafruit 4494
zł39.30
24h
Available quantity: 4
Available
Module with digital barometer BMP388. It measures pressure in the range from 300 to 1250 hPa and communicates via I2C or SPI. Adafruit 3966
zł55.41
24h
Available quantity: 2
Available
Module with a 3-axis magnetic field sensor LIS3MDL. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4479
zł97.77
24h
Available quantity: 1
Available
Module with 9-axis IMU ICM-20948 sensor. The system is an integrated 3-axis accelerometer, gyroscope and magnetometer and a digital motion processor DMP. Communication via I2C or SPI. Adafruit 4554
zł85.92
24h
Available quantity: 6
Available
Module with a precise real time clock (RTC) DS3231. It has an integrated crystal resonator and communicates via the I2C interface. Adafruit 5188
zł78.81
24h
Available quantity: 3
Available
Module with a temperature and humidity sensor based on the SHT40 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4885
zł31.35
24h
Available quantity: 2
Available
Module with 16-bit AD5693R DAC converter with built-in EEPROM memory. Equipped with a STEMMA QT connector, it communicates using the I2C bus. Adafruit 5811