- New
zł178.42 tax excl.
32-bit Makerbase MKS Robin Nano V3.1 motherboard designed for controlling 3D printers, featuring an STM32F407VET6 microcontroller operating at 168 MHz, 512 KB Flash memory and 192 KB RAM. Supports a 12 V or 24 V DC power supply, five stepper motor driver sockets, six motor connectors, two PWM fan channels, and USB and microSD interfaces. Equipped with heater outputs, thermistor inputs and power circuit protection. Makerbase MKS Robin Nano V3.1 (Only motherboard)
The MKS Robin Nano V3.1 motherboard from Makerbase is designed to control 3D printers using FDM/FFF technology. The board features a 32-bit STM32F407VET6 microcontroller with an ARM Cortex-M4 core running at 168 MHz, equipped with 512 KB Flash memory and 192 KB RAM. The controller coordinates the operation of stepper motors, heating systems, fans and sensors used during 3D printing. The board supports Marlin 2.x firmware and is suitable for building new 3D printers or replacing control electronics in existing machines.
The MKS Robin Nano V3.1 operates with a 12 V or 24 V DC power supply and features five StepStick-type stepper motor driver sockets. The pin configuration supports STEP, DIR and ENABLE control signals, as well as UART or SPI communication, depending on the hardware and firmware configuration. The board provides six motor connectors labelled X, Y, Z1, Z2, E0 and E1, with Z1 and Z2 sharing a single motor driver. Two Z-axis motors can therefore be connected and operated using the same control signals. The controller also provides diagnostic signals for implementing sensorless homing functionality.
For controlling external loads, the board provides HE0 and HE1 heater outputs and a heated bed output, along with two independently controlled PWM fan channels. Three temperature measurement inputs, TH1, TH2 and TB, allow thermistors to be connected to the printheads and heated bed. The controller also includes endstop inputs, two filament sensor inputs, a 3D Touch bed levelling sensor interface, power loss detection and automatic shutdown control connections. An additional TTL PWM output provides a control signal for appropriately configured external circuits.

Communication with a computer is provided through a USB interface supporting a virtual serial port. The board also features a USB flash drive connector and a microSD (TF) card slot using the SPI3 interface. The controller provides USART1, SPI2 and UART3 communication lines, along with signal connectors for control interfaces and peripheral devices. Data storage is supported by 4 KB AT24C32DM EEPROM and 8 MB W25Q64JVSIQ external SPI Flash memory. Connector placement and PCB markings facilitate identification of inputs, outputs and signal lines during installation.
The MKS Robin Nano V3.1 PCB measures 110 x 84 mm and features four mounting holes positioned near its corners. Compared with the earlier V3.0 revision, the board uses the STM32F407VET6 microcontroller and provides enhanced protection for selected electronic circuits. The power supply circuit features TVS protection, while the MOSFET drive circuits and temperature measurement inputs incorporate resistor-based protection and Schottky diodes. The board includes screw terminals for connecting power, heaters and the heated bed, as well as pin connectors for other components. Power must be disconnected before installation, and all connections should be checked against the manufacturer's documentation.
Extension module for building a 3D printer or CNC machine. Designed to work with Arduino Mega and A4988 stepper motor drivers
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M5P
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M5P
Universal control module designed for 3D printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays, LED strips and temperature sensors. BIGTREETECH Manta M8P V1.1
A control module designed specifically for Ender 3 printers. It is based on the STM32G0B1 microcontroller, but can use a Raspberry Pi CM4 or CB1 minicomputer as the main module. It has a built-in interface for connecting displays and temperature sensors as well as an EZ connector. BIGTREETECH Manta E3EZ V1.0
A universal control board for a 3D printer based on the 32-bit STM32F429ZE microcontroller. It allows you to connect 8 stepper motors with an operating voltage of up to 60 V and 8 cooling fans. Supports proximity sensor and BL Touch sensor support. BIGTREETECH Octopus Pro V1.0 (F429)
Control module designed specifically for Ender 3, Ender 3 Pro, Ender 5, Ender 5 Plus and CR-10 printers. It is based on the STM32G0B1 microcontroller. It has a built-in interface for connecting displays and temperature sensors. BIGTREETECH SKR MINI E3 V3.0
No product available!
Control module designed specifically for Voron V0 3D printers. It is based on the Raspberry Pi RP2040 microcontroller. It has a shape compatible with Raspberry Pi, so the minicomputer can be mounted directly on the module. BIGTREETECH SKR Pico V1.0
An expansion board equipped with three sockets compatible with stepper motor drivers. It has two EXP control interfaces and can work with motherboards used in 3D printers, e.g. BIGTREETECH SKR V1.3, BIGTREETECH SKR V1.4, BIGTREETECH SKR V1.4 Turbo. BTT EXP-MOT V1.0
No product available!
Extruder controller with CAN communication dedicated to 3D printers. It is designed to work with type 36 stepper motors and is a perfect solution for 3D printing enthusiasts and professionals who are looking for a reliable controller for precise control of the extruder. BIGTREETECH EBB36 CAN (MAX31865)
Extruder controller with CAN communication dedicated to 3D printers. It is designed to work with type 42 stepper motors and is a perfect solution for 3D printing enthusiasts and professionals who are looking for a reliable controller for precise control of the extruder. BIGTREETECH EBB42 CAN (MAX31865)
The Bigtreetech SKR v1.4 is a versatile and powerful motherboard for 3D printers, offering a wide range of features and support for various components. With compatibility for different stepper motor drivers and the ability to expand with WiFi connectivity, it is an excellent choice for anyone looking to optimize their 3D printer and tailor it to their specific needs. BIGTREETECH SKR V1.4
BIGTREETECH EBB SB2240 CAN V1.0 is a reliable and quiet controller module that, thanks to the latest TMC2240 chip, ensures high performance, safety, and long-lasting stable operation of your 3D printer. With extensive diagnostic capabilities and compatibility with popular control boards, it is an excellent solution for demanding users. BIGTREETECH EBB SB2240 CAN V1.0
The Octopus V1.1 is a versatile and powerful motherboard, ideal for advanced 3D printer users. With its robust processor, support for multiple interfaces, and the ability to control 8 axes, this motherboard offers extensive expansion and customization options to meet individual needs. BIGTREETECH Octopus V1.1
BIGTREETECH EBB SB2209 CAN V1.0 is a reliable and quiet controller module that, thanks to the TMC2209 chip, ensures high performance, safety, and long-lasting stable operation of your 3D printer. With extensive diagnostic capabilities and compatibility with popular control boards, it is an excellent solution for demanding users. BIGTREETECH EBB SB2209 CAN V1.0
32-bit Makerbase MKS Robin Nano V3.1 motherboard designed for controlling 3D printers, featuring an STM32F407VET6 microcontroller operating at 168 MHz, 512 KB Flash memory and 192 KB RAM. Supports a 12 V or 24 V DC power supply, five stepper motor driver sockets, six motor connectors, two PWM fan channels, and USB and microSD interfaces. Equipped with heater outputs, thermistor inputs and power circuit protection. Makerbase MKS Robin Nano V3.1 (Only motherboard)
32-bit Makerbase MKS Robin Nano V3.1 motherboard designed for controlling 3D printers, featuring an STM32F407VET6 microcontroller operating at 168 MHz, 512 KB Flash memory and 192 KB RAM. Supports a 12 V or 24 V DC power supply, five stepper motor driver sockets, six motor connectors, two PWM fan channels, and USB and microSD interfaces. Equipped with heater outputs, thermistor inputs and power circuit protection. Makerbase MKS Robin Nano V3.1 (Only motherboard)