![DS - Pololu - 2980 DS - Pololu - 2980](https://kamami.pl/23677-large_default/a4988-stepper-motor-driver-carrier-header-pins-soldered.jpg)
![DS - Pololu - 2980 DS - Pololu - 2980](https://kamami.pl/23677-large_default/a4988-stepper-motor-driver-carrier-header-pins-soldered.jpg)
zł22.06 tax excl.
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2980
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
This version of our A4988 Stepper Motor Driver Carrier ships with 0.1″-pitch male header pins installed as shown in the main product picture, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard.
Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8° per step), a rated voltage of 3.9 V, and draws a current of 0.6 A per coil. Pololu 1204
Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8° per step), rated voltage of 3.8 V, and has a current consumption of 0.67 A per coil. Pololu 1205
Bipolar stepper motor. It has a resolution of 200 steps/revolution (1.8° per step), a nominal voltage of 6.3 V, and draws a current of 0.3 A per coil. Pololu 2294
No product available!
DRV8801 Single Brushed DC Motor Driver Carrier
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
Shield for STM32 Nucleo that allows you to add the possibility of operating a three-phase brushless motor (BLDC) or synchronous permanent magnet (PMSM). It uses the L6230 chip for control. X-NUCLEO-IHM07M1
Module with a stepper motor driver based on the DRV8834 system. It allows you to power a bipolar motor with a current of up to 2 A per phase, without using a heat sink. The system can be powered with a voltage of up to 10.8 V. Pololu 2134
Ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. DRI0041
No product available!
Pololu Dual MC33926 Motor Driver Shield for Arduino
Driver module for two DC brushed motors with current efficiency up to 5 A per channel. It can work with LiPo 2S and 3S packets
No product available!
Module with DC motor driver DRV8876. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 1.1 A. Pololu 4037
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5044
No product available!
The Tic 36v4 USB Multi-Interface High-Power Stepper Motor Controller makes basic control of a stepper motor easy. Pololu 3140
No product available!
DC motor driver with voltage 6.5..40V and maximum continuous current 21A. It has the ability to easily implement the feedback loop and numerous control interfaces. Polol 3149
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
Module with 2-channel DC motor driver DRV8833 designed to work with the Raspberry Pi Pico. It can work with a voltage from 2.7 to 10.8 V and a current of up to 1.2 A. Pimoroni PIM617
Module with a stepper motor driver based on the DRV8434 system. It allows you to power a bipolar motor with a current of up to 1.2 A per phase and a voltage from 4.5 V to 48 V. Pololu 3762
A single-channel DC motor controller with a UART TTL interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5077
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2980