ESC BLHeli-S 45A brushless motor driver

An advanced speed controller designed to power three-phase brushless motors in various applications, such as driving robots, walking robots or gimbals. Supports input voltage range from 12V to 56V. Maximum constant current is 60A. Makerbase ODrive-S

Brushless motor driver module (ESC regulator) with current efficiency up to 35 A

The ODrive3.6 ESC speed controller is designed to power two three-phase brushless motors in various applications, such as driving robots, walking robots or gimbals. Supports input voltage range from 12 V to 56 V and maximum current up to 60 A. Makerbase ODrive3.6

The X-NUCLEO-IHM11M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN230 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

Brushless motor driver module (ESC regulator) with current efficiency up to 20 A. Uses BLHeli_S software

A dual-channel BLDC controller capable of controlling two motors simultaneously using precise FOC vector control. Equipped with the EG Driver Chip, an INA181A2 amplifier, and a 1 mΩ sensing resistor, it provides accurate current measurement and stable operation at peak currents up to 12 A. It supports a variety of encoders and sensors, and its compatibility with ESP32 modules makes it easy to integrate into projects. Makerbase DUAL FOC PLUS

The X-NUCLEO-IHM16M1 motor driver expansion board is based on the STSPIN830 monolithic driver for three-phase brushless motors. It represents an affordable, easy-to-use solution for driving brushless motors in your STM32 Nucleo project, implementing single and three-shunt current sensing

Brushless DC motor driver (BLDC) with speed regulation by potentiometer or PWM signal. It can operate motors powered with the voltage from 6 to 60 V with a current consumption of up to 16 A

An advanced speed controller designed to power three-phase brushless motors in a variety of applications such as electric scooters, electric skateboards and electric bicycles. It supports an input voltage range of 8 V to 60 V, which corresponds to 3S to 13S for LiPo batteries, and a maximum current of up to 50 A. Makerbase VESC MINI 6.7 Pro

ESC controller module for a brushless motor with a current capacity of up to 40 A. It can work with LiPo packages from 3S to 6S. Uses BLHeli_32 software. Skystars Talon32

ESC controller module for a brushless motor with a current capacity of up to 80 A. It can work with LiPo packs from 5S to 12S. Uses BLHeli_32 software. FLYCOLOR X-CROSS HV

The 7A 1-2S BLheli_S XSD7A Miniature Brushless Motor ESC Controller is a compact, high-performance device ideal for controlling brushless motors in small projects. Thanks to its low weight and solid power, it is suitable for drones, RC models and other applications requiring precise motor control.

The X-NUCLEO-IHM17M1 is a low voltage three-phase brushless DC motor driver expansion board based on the STSPIN233 for STM32 Nucleo. It provides an affordable and easy-to-use solution for the implementation of portable motor driving applications such as thermal printers, robotics and toys

This BLDC motor controller, based on the Allegro A89301 chip, enables sensorless control over a wide voltage range from 5.5 V to 48 V and phase current up to 11 A without additional cooling. It supports four control modes: analog voltage, PWM signal, pulse frequency, and via an I²C interface with the ability to configure parameters and save settings to EEPROM. The Field-Oriented Control (FOC) algorithm ensures quiet and efficient operation, while built-in protection protects the system against short circuits, reverse polarity, and undervoltage. Pololu 5357

A controller that allows you to control any 3-phase BLDC motor. It is equipped with built-in WiFi and Bluetooth connectivity as well as an integrated TMAG5273 Hall effect sensor and INA240A1 current sensor amplifiers, thanks to which it allows the use of advanced FOC algorithms. SparkFun ROB-22132

Waveshare DDSM Driver HAT (B) is an advanced hub motor driver for DDSM400 motors, based on the ESP32, featuring both wired (USB, UART) and wireless (WiFi, ESP-NOW) communication. It supports control of up to 6 motors using JSON commands and integrates with Raspberry Pi, making it a suitable solution for mobile robotics and multi-motor system projects.