ULN2003 stepper motor driver module set and 5V stepper motor
ID: 575268
zł13.11
Tax included
zł10.66 tax excl.
A set consisting of a stepper motor driver module based on the ULN2003 system and a stepper motor powered with 5V voltage.
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
A set consisting of a stepper motor controller module based on the ULN2003 system and a stepper motor powered with 5 V. The ULN2003 system includes in its structure 7 pairs of transistors in the Darlington system, with a common emitter. Ideal for controlling motors or relays. The output of each pair of transistors is protected by a diode.
properties
Stepper motor:
- Resolution: 5.625 x 1/64
- Torque:> 34.3 mNm
- DCR: 200ohm +/- 7% (25'C) - temperature: <40K (120Hz)
- Insulation resistance:> 10 MΩ (500V)
- Noise: <40dB (120 Hz, no load, 10 cm)
- Dielectric strength: 600 V AC / 1 mA / 1 s
- Power supply: 5 V
- Cable length: 24 cm
- Diameter: 28 mm
Driver module:
- Power supply: 5-12 V
- 4 signaling diodes
- XH-5P connector
- Dimensions: 40.5 x 21.3 mm
Included
- ULN2003 driver module
- 5 V stepper motor
575268
Data sheet
- Shaft diameter
- 5 mm
- Resolution
- 64 kroki/obr
- Torque
- 300 g-cm
- Coil resistance
- 50 Ω
- Coil current
- 100 mA
- Output current
- 500 mA
- Number of channels
- 1
- Voltage
- 5 V
- Supply voltage min
- 5 V
- Supply voltages max
- 12 V
- Weight
- 35 g
You might also like
The ULN2003A system consists of seven Darlington chips, housed in a DIP16 housing.
zł1.40
24h
Available quantity: 80
Available
Available
No product available!
Other products in the same category (16)
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
zł85.90
24h
Available quantity: 4
Available
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
zł47.86
24h
Available quantity: 3
Available
Module with the TMC2209 bipolar stepper motor driver. It enables control with a supply voltage ranging from 4.75 to 29 V and a current of up to 2.8 A
zł21.06
24h
Available quantity: 43
Available
Module with a stepper motor driver based on the DRV8834 system. It allows you to power a bipolar motor with a current of up to 2 A per phase, without using a heat sink. The system can be powered with a voltage of up to 10.8 V. Pololu 2134
zł42.80
6 weeks
No product available!
The stepper motor driver with Allegro A4988 (A4988 Stepper Motor Driver Carrier) allows you to supply a bipolar current of up to 2A per phase. The system can be supplied with voltage up to 35V, in the set there is a heat sink. It is compatible with Polol 1182
zł5.60
24h
Available quantity: 83
Available
No product available!
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł466.03
24h
Available quantity: 3
Available
Available
STSPIN220 stepper motor driver module with a low voltage range of 1.8...10V and 1.1A working current. The controller allows you to control the motor motion up to 9 different resolutions (up to 1/256 steps). Pololu 2877
zł45.85
24h
Available quantity: 1
Available
A4988 Stepper Motor Driver Carrier
zł68.46
24h
Available quantity: 5
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł116.17
4 weeks
No product available!
The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł288.91
6 weeks
No product available!
Compact stepper motor controller with the TMC2208 system with operating voltage from 4 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications
zł16.16
24h
Available quantity: 5
Available
MP6500 Stepper Motor Driver Carrier, Digital Current Control
zł33.70
24h
Available quantity: 2
Available
TB6612FNG dual DC motor controller module. It can be used as a stepper motor driver or solenoid driver. Adafruit 2448
zł39.89
24h
Available quantity: 3
Available
The stepper motor driver with the MP6500 system allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35 V. Pololu 2966
zł36.20
24h
Available quantity: 1
Available
A set consisting of a stepper motor driver module based on the ULN2003 system and a stepper motor powered with 5V voltage.