

Extension module with a driver for two stepper motors based on the DRV8825 system. It allows you to control drives with a working voltage from 8.2 V to 28 V with a maximum current of 2.5 A, regulated by a potentiometer. Built-in switches allow you to select microstepping from full step to 1/32 step.
1. Raspberry Pi GPIO | 5. Power supply interface 8,2 - 28 V |
2. Motor interface | 6. Motor power switch |
3. MP1482 power chip | 7. DIP switch |
4. DRV8825 motor driver | 8. Potentiometer |
The module has protection against overload, overheating and too low voltage, and the 5 V stabilizer allows you to directly power the RPi minicomputer from the expansion board. The board has a 40-pin connector compatible with Raspberry Pi and Jetson Nano. It will be used in projects using stepper motors, incl. 3D printers, plotters. Full documentation and sample programs are available on the product page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 1GB RAM LPDDR4, Broadcom VideoCore VI layout.
No product available!
The latest version of the Raspberry Pi series: Raspberry Pi 4 model B with quad-core SoC (Broadcom BCM2711, Cortex-A72) working at 1.5GHz, 2GB RAM LPDDR4, Broadcom VideoCore VI.
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 4 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
No product available!
The long-awaited Raspberry Pi 4 model B with the SoC Broadcom BCM2711 SoC (4 x Cortex-A72) running at 1.5GHz, 8 GB LPDDR4 RAM and the Broadcom VideoCore VI graphics chip
Extension module with a driver for two stepper motors based on the HR8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT (B)
NVIDIA development kit with the ARM Cortex A57 1.43GHz CPU system and the Maxwell graphics system consisting of 128 cores supporting CUDA technology. The module has 4GB DDR4 RAM, 16GB eMMC and an attached 32GB USB memory and 64GB microSD card. Waveshare JETSON-NANO-DEV-KIT
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5049
No product available!
The official extension module (HAT) dedicated to the Raspberry Pi. It allows you to control LEGO SPIKE Prime motors and service LEGO sensors. Raspberry Pi SC0622
PCA9685 servo controller module dedicated to Raspberry Pi minicomputers. Allows control of 16 PWM channels. Waveshare Servo Driver HAT (B)
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5055
No product available!
This programmable module combines with a Raspberry Pi to serve as the control center of a small robot or electronics project. Its Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader, and the board includes dual motor drivers that can deliver 1.8 A per channel to two brushed DC motors.
The module with a 4-channel L293D DC motor driver, designed to work with the Raspberry Pi. It can work with a voltage from 6 to 24 V and a current of up to 600 mA. SB Components 08001
Atmel ATmega32U4 microcontroller comes preloaded with an Arduino-compatible bootloader, and the board includes dual motor drivers that can deliver 1.7 A per channel to two brushed DC motors. Pololu 3119
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5057
No product available!
Dual DC motor controller designed for Raspberry Pi, which enables the engine to be supplied with voltage in the 4.5-28V range and power consumption in continuous operation of 2.6A (5A in peak) of two DC motors. Self-assembly set. Pololu 2761
HAT with two-channel DC motor driver for Raspberry Pi. It has an operating voltage from 6 to 24 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron HAT-MDD10
Raspberry Pi Expansion Board, DC Motor / Stepper Motor Driver
DFRobot 0592 is a Raspberry Pi DC motor driver board with built-in encoder interface that can drive a 2-way DC motor and a DC motor with encoder
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
No product available!
PiFace Relay Motor Control Extra (Board) for Raspberry Pi
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5056
No product available!
HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280
Extension module with a driver for two stepper motors based on the DRV8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT