

Pump up the volume with this 20W stereo amplifier! This slim little board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Power it with 5-12VDC using the onboard DC power jack and plug stereo line level into the 3.5mm stereo headphone jack and jam out with ease. Since it's class D, its completely cool-running, no heat sinks are required and it's extremely efficient - up to 93% efficiency makes it great for portable or battery powered rigs.
We like the MAX9744 amplifier at the heart of this board because its very easy to use, but it also has both analog and digitalvolume control capability. Use a single 1KΩ pot (we include one) to adjust volume analog-style. Or hook it up to your favorite microcontroller and send I2C commands to set 64-steps of volume amplification.
Dimensions (without 0.1" header or terminal blocks):
We took this lovely chip and wrapped it up into a breakout for you, with polarity-protection, jacks and terminal blocks, i2c level shifting, and a spot to solder in a volume pot.
Each order comes with one MAX9744 breakout board with all surface-mount parts fully assembled and tested. We also include 3 x 2pin and 1 x 3pin terminal blocks, a 470uF power filter capacitor and 1KΩ trim pot. To use this board, a little soldering is required to attach the terminal blocks and other components, but its fairly easy and expect it should take less than 15 minutes.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
No product available!
A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)
Module with the WM8960 audio codec, which allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Waveshare WM8960 Audio HAT
No product available!
Stereo audio amplifier based on the TPA3116D2 chip. It can be powered with the voltage from 12 to 26 V and has two outputs with a power of 120 W
2-channel stereo audio mixer module. It has four outputs, on which the summed signal from 2 inputs is available. It is powered with the voltage from 5 to 19 V
Stereo audio amplifier based on the TPA3116D2 chip. It can be powered with the voltage from 12 to 24 V and has two outputs with a power of 100 W
No product available!
The TPA3116D2 amplifier module is a digital class D amplifier, offering 2x50W of power for stereo channels and 100W for the subwoofer, powered by 12V-24V. Thanks to the built-in NE5532 low-pass filter, it provides clean bass sound, and three potentiometers allow you to adjust the volume and cutoff frequency.
No product available!
Class D digital audio amplifier with Bluetooth module. It has two channels with a power of 50 W and can work with speakers from 4 to 8 Ω. It is powered with the voltage in the range from 9 to 24 V. NS-01G
No product available!
HiFi stereo tube amplifier based on 6J1 and 6P1 tubes. Designed for use with loudspeakers up to 3 W and an impedance of 4 Ω or 8 Ω
Audio module with speakers designed to work with the Raspberry Pi Pico. Waveshare Pico-Audio
Class D PAM8406 stereo digital audio amplifier module. The system allows you to connect two speakers with an impedance of 4 to 8 Ω and a power of 5 W per channel
No product available!
Audio preamplifier based on NE5532 chips. Equipped with an input selector function. Display and remote control included
Module with the PAM8904 controller designed specifically to control piezoelectric elements. The amplifier operates over a wide frequency range, up to 300 kHz, and allows for gain up to approximately 13 Vpp. Adafruit 5791
Audio amplifier with three output channels. It can be powered with the voltage from 5 to 26 V and has two outputs with a power of 50 W (left and right) and one with a power of 100 W (bass). Equipped with Bluetooth 5.0 communication. XY-S100L
2-channel stereo audio mixer in a metal housing. It has four outputs, on which the summed signal from 2 inputs is available. It is powered with the voltage from 5 to 19 V
The 2x40W Bluetooth amplifier module XY-P40W is a versatile audio amplifier with a wide voltage range and Bluetooth 5.0 compatibility, enabling wireless audio transmission at a distance of up to 15 meters. It has protective mechanisms that make it not only a powerful but also a safe tool for designing your own audio devices.
No product available!
The Class D digital audio amplifier module has two channels with a power of 15 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
TDA2030A mono digital audio amplifier module. The system allows you to connect one loudspeaker with an impedance from 4 to 8 Ω and a power of 18 W
The board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Adafruit 1752