Best sellers
There are 17538 products.
5" TFT LCD display with touch screen. It was equipped with DSI interface for image display and I2C interface for touch screen. Resolution 800x480 pixels. DFRobot DFR0550
The module with a 16x2 character LCD display with blue backlight. It is equipped with an AiP31068 controller that implements communication via the I2C interface. Waveshare LCD1602 I2C Module
Power supply module with an input voltage from 6 to 12 V and a configurable output voltage of 3.3 V or 5 V. It has holes with a 2.54 mm pitch. Perfect for use with a breadboard. SparkFun PRT-13032
Set of "sleeping lion" with the educational module micro: bit. It consists of a main plate, noise: bit and felt elements, thread and needle to create the toy. Pimoroni PIM363
With the help of a thermocouple, it is possible to measure the temperature of the air and the surface. The use of a steel stainless steel tip in a K-type thermocouple allows the temperature to be measured up to 500 ° C. The cord length is approximately 100 centimeters. Adafruit 3245
The FS5106R is a standard-sized servo that has been built by FEETECH specifically for continuous rotation, making it an easy way to get your robot moving. It features two ball bearings on the output shaft for reduced friction, and it offers easy access to the rest-point adjustment potentiometer.
Ultrasonic distance sensor with a range of 30 to 500 cm. Powered from 5 to 12 V, it communicates via RS485 interface. DFRobot SEN0519
The board is equipped with ATSAMD21 microcontroller with ARM Cortex-M0 core and SPI Flash memory, GPIO pins and RGB diode. Adafruit 3727
Module with SGP30 gas sensor. The sensor communicates via the I2C interface. SGP30 system contains several elements reacting to various metal oxides, which allows for more accurate determination of air quality. Adafruit 3709
Optical rain sensor module for detecting the state of rainfall on glass. It is configured via the UART interface and returns rain intensity information via this bus. DFRobot SEN0545
The FS5106B is a general-purpose, low-cost standard analog servo from FEETECH. Two ball bearings help reduce friction and improve performance. Servo horns and associated hardware are included.
Key specs at 6 V: 0.16 sec/60°, 80 oz-in (6 kg-cm), 41 g
Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. Adafruit 3405
Camera set with IMX477 sensor with 12 MPx matrix, allows for remote camera rotation, tilt angle and zoom control. Works with Raspberry Pi minicomputers. Swivel base included. ArduCAM B0167B12
Module with the PIR EKMB1107112 motion sensor, the standby power consumption of up to 1 uA. SparkFun SEN-17373
The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.
Module with PIR EKMB1107112 motion sensor, power consumption in standby mode up to 1 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17375
M12 mount lens. It has a focal length of 8 mm mm and an FoV viewing angle of 69.5°. It is designed to work with the Raspberry Pi HQ camera M12. Waveshare WS0698012
The expansion module is designed to work with the micro:bit educational board. It can control 3 servos and 2 DC motors. Waveshare Motor Driver for micro:bit
QUICK Q303-4.2D soldering tip with sensor for: Quick 202D