Best sellers

IMXRT1050-EVKB is an evaluation set from NXT with i.MX RT1050 ARM Cortex-M7 600 MHz processor, 256 MB SDRAM memory, USB Host and OTG connector, Ethernet interface and SD card slot. IMXRT1050-EVKB

Module with 6 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4206

Compute Module IO Board Plus is a prototype board that allows you to connect Raspberry Pi CM3 module and CM3L module. It is equipped with numerous GPIO pins, HDMI port, USB ports, camera and display ports. Compute Module IO Board Plus

Module with 5 colored buttons. Each button is powered independently and has an output informing about its status

Mini plotter construction kit. The structure is made of wood, a felt-tip pen is used as a writing element. The device is powered by two 1.5V AA batteries

Dual DC motor controller designed for Arduino, which enables the motor to be supplied with voltage in the 4.5 ... 28V range and power consumption in continuous operation of 2.6 A (5A at the top) of two DC motors. Polol 2520

Espruino module with Bluetooth LE based on MDBT42Q system with Nordic Semiconductor nRF52832 microcontroller. The module has a pre-installed JavaScript interpreter. Adafruit 3876

4-digit LED watch in the form of a kit for self-assembly. Equipped with a light sensor, thermistor and buzzer, it is controlled by two buttons

The STEVAL-FKI868V2 evaluation board is based on the S2-LP sub-1GHz ultra-low power low data-rate transceiver suitable for ISM bands and wireless M-Bus. The NUCLEO-L053R8 motherboard is equipped with an STM32L0 low power microcontroller to control the S2-LP

Speaker for micro:bit is an expansion module with a loudspeaker designed for micro:bit with volume control and headphone output. Speaker for micro:bit

DC-DC Step-up converter module based on the U3V70F12 system. Input voltage 2.9-12V, output voltage 12V, maximum current 10A. Two mounting holes. Pololu 2895

Module with an IO pin expander based on the TCA9534 system. It allows you to add 8 GPIO pins to an I2C-controlled project. SparkFun DEV-17047

Self-adhesive aluminum tape 50mm 40m designed for thermal protection, shielding, and discharge of electric charges.

Module with 2 QTR type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4102

Module with 2 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4202

Module with 4 QTRX type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4304

The Semi Flexible Monocrystalline Solar Panel is a flexible monocrystalline solar panel with a 5V output voltage and a current capacity of 1 x 29 x 15 x 0.135 cm. DFRobot FIT0600

Module with 6 QTR type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4106

Mini keyboard with 16 buttons and RGB backlight. Equipped with a connector compatible with Grove, it communicates via the I2C interface. Adafruit 3954

Vorel - 76640